Kodak K7600-C - Manual

Model K7600-C
Compatible with KODAK Li-Ion
Rechargeable Digital Camera Batteries
KLIC-5000, KLIC-5001, KLIC-7000,
KLIC-7001, KLIC-7002, KLIC-7003,
KLIC-7004, KLIC-7005, KLIC-7006,
KLIC-8000
Kodak
KODAK Li-Ion
Universal Battery
Charger
Operating
Instructions
2F6702
Use the KODAK Universal Li-Ion Battery Charger to charge
KODAK Li-Ion Rechargeable Digital Camera Batteries.
Features
• Automatic polarity detection
• Top-off charging for a full charge
• LED indicator displays charging mode
• Timer protection
• Overcharge protection
• Abnormal battery detection indicates faulty battery and halts
charging
Operating Instructions
1. Snap the charging plate into the charger base.
- Charging Plate
2. Insert a plug appropriate for your region.
3. Connect the AC adapter to the bottom of the charger base,
then plug into a wall outlet.
4. Pull down and hold the battery support, then insert the battery
so it rests against the stop at the right side of the charging
plate. The 2 pins on the charging plate must touch the 2 outer
contacts on the battery.
NOTE; The charger automatically determines the correct
polarity (-h/-).
Battery Stop
Battery Support
5. Gently release the battery support to hold the battery securely
In place during charging.
LED indicators
Blinking amber=charging
Steady amber=battery charged
Amber=3.6V battery In:
Green = 7.2V battery installed
Green = power on
Blinking green + red = error
Approximate charging times for fully discharged batteries:
KLIC-5000 170 min.
KLIC-5001 260 min.
KLIC-7000, KLIC-7001 90 min.
KLIC-7002 75 min.
KLIC-7003 160 min.
KLIC-7004 160 min.
KLIC-7005 85 min.
KLIC-7006 95 min.
KLIC-8000 210 min.
Using the Car Adapter Plug
Connect the car adapter plug to the bottom of the charger base,
then plug the other end into your car’s 12V socket.
NOTE: Unplug the charger from the 12V socket when the car is
not mnning, as the charger may draw current and drain the car
battery.
Troubleshooting
• No Indicator lights
Confirm that the AC adapter or car adapter plug is firmly
connected to the charger and either the wall outlet or 12V
socket.
If using the car adapter plug, confirm whether the ignition needs
to be on.
• Power light only
Battery is already fully charged.
Battery is inserted incorrectly. Remove and insert battery
correctly.
Dirt on contacts. Clean battery and charger contacts.
• Power and Charge Status indicators both blink
Battery is defective. Replace battery.
• Hissing noise In charge mode
Normal operation due to advanced switching circuitry.
Technical Specifications
Input voltage:
Output voltage:
100-240V>-5Q/60Hz 280mA
DC 12V=700mA 8.4VA
IMPORTANT SAFETY
INSTRUCTIONS-Save These
Instructions
• DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS.
• For connection to a supply not in the U.S.A., use an attachment
plug adapter of the proper configuration tor the power outlet.
This battery charger is intended to be correctly oriented in a
vertical or floor mount position.
CAUTION:
• Charge only compatible Li-Ion rechargeable batteries. Other
types of batteries may burst causing personal injury and damage.
• Risk of electric shock. Use only in dry locations.
• Do not operate charger if it has been damaged.
• To reduce the risk of electric shock, unplug charger from outlet
before attempting any maintenance or cleaning.
• Be sure to use charger with correct voltage: AC 100-240V.
• Do not insert any objects (such as a screwdriver or metal wires)
into the charger.
• Do not modify or disassemble.
• If something appears wrong with the charger and/or batteries,
disconnect from the electric outlet immediately.
• Keep out of reach of infants. Children may use only under strict
parental supervision.
• Store In a dry, cool place.
Recommended temperature ranges for use:
Li-Ion
To use (discharge) the batteries 32*-122“ F (0“-50* C)
To charge the batteries 32'’-^'’ F (0"-^'’ C)
To store the batteries -4'’-86‘’F(-20'’-30“C)
Regulatory Information
FCC compliance and advisory
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasortable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed or used in accordance with the instmctions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to coned the interference by one or more of the
following measures;
1) reorient or relocate the receiving antenna; 2) increase the separation
between the equipment and the receiver; 3) connect the equipment to an
outlet on a circuit different from that to which the receiver is connected: 4)
consult the dealer or an experienced radio/TV technician for additional
suggestions.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment Where
shielded interface cables have been provided with the product or specified
additional components or accessories elsewhere defined to be used with the
installation of the product, they must be used in order to ensure compliance
with FCC regulation.