Cobra Electronics XRS 9700 - Manual (Page 7)

EasySet Programming
Nothing comes close to a Cobra ® 9
EasySet Programming
8 English
Your Detector Your Detector
EasySet Programming Menu
Mode Tone Or Voice Visual Setting Result
Set City
mode
default* Two (2) beeps City X A single beep sounds when the
signal is first detected.
One (1) beep City X
beep Off Audio for all X band alerts are blocked
until signal strength reaches Level 3.
One (1) beep City X+K Combines the City X mode with
prevention of K band audio alerts
until signal strength reaches Level 2.
IntelliMute
mode Two (2) beeps IntelliMute On All alerts (except for strobe signals
from emergency vehicles) are
automatically muted below the
engine rev point you set.
One (1) beep IntelliMute Off Normal operation.
Set IntelliMute
RPMs
(not shown
if IntelliMute
is off) One (1) beep Set IntelliMute
(see page 15
to set activation
point) Allows you to set the engine
rev point while using IntelliMute.
AutoMute
mode Two (2) beeps AutoMute On The audio volume of all alerts will be
automatically muted after four (4) seconds
for as long as the signal is detected.
One (1) beep AutoMute Off All alerts will sound at full volume
for as long as the signal is detected.
Set compass One (1) beep Set Compass
(see page 17
to calibrate
compass) Allows you to calibrate the compass.
Pop Detect
mode Two (2) beeps Pop Detect On The unit will detect Pop signals.
One (1) beep Pop Detect Off The unit not will detect Pop signals.
EasySet Programming Menu
Mode Tone Or Voice Visual Setting Result
VG-2 Detect
mode Two (2) beeps VG-2 Detect On The unit will detect VG-2 signals.
One (1) beep VG-2 Detect Off The unit will not detect VG-2 signals.
VG-2 Audio
mode (not
shown if VG-2
detect is off) Two (2) beeps VG-2 Audio On With VG-2 Detect on, the unit will give
audible alerts for VG-2 signals.
One (1) beep VG-2 Audio Off With VG-2 Detect off, the unit will give
only visual alerts for VG-2 signals.
Spectre 1
Detect mode Two (2) beeps Spectre 1
Detect On
The unit will detect Spectre 1 signals.
One (1) beep Spectre 1
Detect Off The unit will not detect Spectre 1 signals.
Spectre 1
Audio mode
(not shown if
Spectre 1
detect is off) Two (2) beeps Spectre 1
Audio On
With Spectre 1 Detect on, the unit will
give audible alerts for Spectre 1 signals.
One (1) beep Spectre 1
Audio Off With Spectre 1 Detect off, the unit will give
only visual alerts for Spectre 1 signals.
SmartPower
mode Two (2) beeps SmartPower
On
SmartPower is on.
One (1) beep SmartPower
Off SmartPower is off.
X Band detect
mode Two (2) beeps X Band On The unit will detect X Band signals.
One (1) beep X Band Off The unit will not detect X Band signals.
Set display
Dim mode
default* Two (2) beeps Display Dim Partially dimmed for dusk or night driving.
One (1) beep Display
Dimmer More dimmed for dusk or night
driving.
One (1) beep Display Dark Display is off.
Restore
factory
settings One (1) beep Restore
Factory
Settings Resets user modes and settings to
factory default.
Exit program One (1) beep EXIT
PROGRAM Allows you to exit Program mode.
* The settings for these user modes can also be changed with the one (1) button method.
See description of each user mode (pages 10 and 24) for details.
This EasySet programming menu lists all of the modes and settings
you can choose from after you have entered Program mode as
described on page 7.