Philips QC5570-40 - Manual (Page 2)

Table 1 Precision and Regular Combs
Precision Comb
Barber Remaining
Setting Hair Length
Regular Comb
Barber Remaining
Setting Hair Length
• 3/64 in./1mm #1 1/8 iny3mm
#1/2 1/16 inyi.5mm • 3/16 in25mm
• 5/64 iny2mm #2 9/32 iny7mm
• 3/32 iny2.5mm #3 3/8 in29mm
#1 1 /8 in./3mm • 7/16 inVIlmm
#4 1/2 In713mnn
#5 5/8 inyi5mm
TIP: Use different settings to create a natural and
smooth transition between various hair lengths from
your neckline to the top of your head (Fig. 1).
Using the rotating head
k At the starting clipping position of 0' (pointing
forward), turn the rotating head 45’ or 90’ to
the left or right to adjust the position of the
cutting element to the part of your head you
are clipping (Fig. 8).
H Turn the rotating head left or right to the
desired clipping position. At each position you
will hear a ‘click’ (Fig. 9).
Always adjust the position of the cutting element
by turning the rotating head. Do not turn the
rotating head by holding the cutting element or
the comb attachment.
B The rotating head allows you to hold and use
the Clipper like a styling comb (Fig. 10).
Do not turn the rotating head more than 90° to
the left or right.
B Press the ON/OFF button to turn on the
appliance.
□ Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result.
B Since all hairs do not grow in the same
direction, move the Clipper slowly over the
crown from different directions (i.e. upwards,
downwards and across) to achieve an even
result (Fig. 11).
Q Always move the Clipper slowly against the
direction of hair growth.
B
Make overlapping passes over the head to
ensure that all hairs that should be cut are
cut.
□ As you clip different areas of your head,
adjust the position of the rotating head
so that the rotating head position is most
comfortable for you.
D For best results with curly, sparse or long
hair, use a styling comb to guide the hair
towards the Clipper.
EE
Turn the Clipper off regularly during clipping
and remove the hair comb to blow and/or
shake out hair that has accumulated.
When you remove the comb, the selected setting
does not change.
TiP-.Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
Contouring without a comb
attachment
► Use the Clipper without a comb attachment to
clip very close to the skin (1/32 in/O.Smm).
► Be careful when you are clipping without a
comb as when the Clipper is turned on it will
remove every hair it touches.
D Remove the comb by pulling it off the
rotating head (Fig. 12).
Never pull at the flexible top of the comb. Always
pull at the bottom part.
B
To contour the hairline around the ears,
comb the hair ends over the ears.
B Press the ON/OFF Button to turn on the
appliance.
Q Tilt the Clipper in such a way that only one
edge of the cuttiing element touches the hair
ends. Be careful not to trim too much. The
hairline should be close to the ear (Fig. 13).
B
To contour the neckline and the sideburns,
turn the Clipper and make downward
strokes (Fig. 14).
NOTE: Move the Clipper slowly and smoothly.
Simply follow the natural hairline.
B
Adjust the position of the rotating head to
make contouring easier.
Cleaning
I Clean the Clipper after each use.
I Always switch Clipper OFF, unplug and remove
power supply cord from Clipper before
cleaning.
I Do not use compressed air, abrasive cleaning
agents, scourers or aggressive liquids such as
gasoline, acetone or ethereal oils to clean
the Clipper and attachments.
I Never clean, replace or remove Clipper
attachments with motor ON.
I Do not use Clipper if cutter or cutting
element are damaged or broken as injury may
occur.
I
Use a soft, dry cloth to clean Clipper handle.
During Use:
► If cut hairs have accumulated in the comb
area, remove hairs by shaking, blowing or using
cleaning brush provided.
Cleaning the Cutting Element and
Combs After Each Use:
D Make sure the Clipper is switched OFF
and disconnected from the electrical outlet.
B
Remove any comb attachment (Fig. 12).
B
Blow and/or shake out any hair that may
have accumulated in the comb.
□ Rinse the comb under the tap or clean it
with the cleaning brush supplied.
B
Apply pressure to the center of the cutting
element with your thumb (1) until it releases
from the rotating head (2) (Fig. 15).
Be careful that the cutting element does not fall to
the floor.
B
Clean the cutting element under the tap
or with the brush supplied (Fig. 16).
Make sure the cutting element is thoroughly dry
before reattaching to Clipper
PHILIPS
^NORELCO
B
Clean the inside of the rotating head under
the tap or with the brush supplied (Fig. 17).
B Clean the handle and the adapter with the
cleaning brush supplied or with a dry cloth.
D Insert the notch of the cutting element or
precision trimmer into the slot on the
rotating head and push until the cutting
element‘clicks’ into place (Fig. 18).
This Clipper has no other user-serviceable parts.
For assistance call 1-800-243-3050.
Assistance
For assistance, visit our website:
www.philips.com/support or
call toll free: 1-800-243-3050
Online information is available 24 hours a day, 7
days a week.
Storage
I
Be sure Clipper is turned OFF. Remove cord
from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
I Do not wrap cord around Clipper when
storing.
I Store cord in a safe location where it will not
be cut or damaged.
I Do not place or store Clipper where it can fall
or be pulled into a tub or sink, water or other
liquid while plugged in.
Battery Removal
► This Philips Norelco Clipper contains a
rechargeable Lithium-Ion battery which must
be disposed of properly (Fig. 19).
k Battery may only be removed when
Clipper is to be discarded.
I
For assistance, visit our website,
www.philips.com/support or
call toll free: 1-800-243-3050
O Unplug electrical cord from outlet and
Clipper before dismantling Clipper.
B
Allow Clipper to run until the battery is
empty/depleted.
B
Turn Clipper OFF.
Q Remove any comb attachment.
B
Use a screwdriver to remove the upper
housing part of the Clipper (Fig. 20).
B Use a screwdriver to open the inner body
of the Clipper.
B
Use a screwdriver to remove the battery
from the Clipper (Fig. 21).
Headgroom
Plus
QC5570
Rechargeable
Cordless/Cord
Always here to help you
Register your product and get support at
www.norelco.com/register
4222 002 8311 2
B
Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag.
EE
Discard your Clipper. Do not attempt to
plug electrical cord into the outlet or
recharge the Clipper after the battery has
been removed.
ED Contact your local town or city officials
for battery disposal information or call
1 -800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
Full Two-Year Warranty
Philips Electronics North Amenca Corporation warrants each new Philips
Norelco product. Model QC5570 (except cutters and combs) against
defects in matenals or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective product
without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident misuse or abuse, tack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FORWARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZEO REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FORANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.ph(lips.com/
norelco or call 1 -800-243*3050 for assistance. It is suggested that for
your proteaion you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipnnent is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Elearonics North Amenca Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
fixMTi state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you.
•Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics Nordi America Corporation
RO. Box 10313. Stamford. CT 06904
This symbol on the product's nameplate means it is
listed by Underwriters' Laboratories. Inc.
Noreko IS a Registered Trademark of Phil?« Electronics
North America Corporation.
PHIUPS is a Registered Trademark of KonmJdijke Philips Electronics N.V.
© 2013 Philips Electronics North Amenca Corporation, All Rights Reserved.
PHIUPS
^NORELCO
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Clipper send the product back and we’ll refund you the
full purchase price.
The Clipper must be shipped prepaid by insured
mail, insurance prepaid, have the original sales
receipt, indicating purchase price and date of
purchase, and the money-back guarantee return
authorization form enclosed. We cannot be
responsible for lost mail.
The Clipper must be postmarked no later than
45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6-8 weeks AFTER
receipt of returned product.
B
Cut the wires with household scissors.