Morley ECHO-PLUS ECHO CHORUS VIBRATO (ECV) - Manual

THANK YOU!
For purchasing a Morley® pedal.
Please take a few minutes to familiarize yourself with the
features of your new pedal. With common sense handling,
it should last for years. We know you will appreciate the
rugged construction of your Morley®. Most of all, we hope
you enjoy using it as much as we enjoyed building it.
AC ADAPTER
Use Morley’s 9-volt DC 300 milliamp regulated adapter
only. Using a non-regulated adapter could cause a low
frequency hum in your amplifier and may damage the
pedal.
BATTERY
The ECHO PLUS is designed to use one 9 volt battery
when not using an adapter. We suggest you use a good
quality alkaline battery.
To prolong battery life, unplug your cord completely from
the input jack when not using the pedal. When the pedal is
not used for extended periods, we recommend you remove
the battery from the pedal or replace it every six month to
prevent leakage problems.
CONNECTIONS
9V: Connect Morley 9 volt regulated 300 mA adapter to
this jack.
INPUT: Input jack. Plug instrument into this jack using
1/4” guitar cable.
OUTPUT (MONO): Used when not using the stereo output
jack. Connect amplifier to this jack using a 1/4” guitar
cable.
OUTPUT (STEREO): Used for stereo applications. Connect
a second amplifier to this jack using a 1/4” guitar cable.
NOTE: You’ll find cords fits very tightly into our input and
output jacks. The tight fits helps prevent the cord from
becoming accidentally unplugged from the pedal. Make
sure the cords are completely plugged in for best results.
CONTROLS
The Echo-Plus control are divided up into two sections:
Echo related and Chorus Related. To explain, let’s focus on
one effect at a time.
ECHO RELATED (see diagram #1):
A. EFFECT ON/OFF SWITCH: Turns on and off the
effects.
B. EFFECT LED: Lights up when effects switch is engaged.
C. ECHO “DELAY” CONTROL: Controls the amount of
delay time from 0 to 300 milliseconds.
D. ECHO “REPEATS” CONTROL: Adjusts the amount of
repeats the ECHO will reproduce when a note is played.
Ranges from one repeat to multiple repeats.
E. TREADLE CONTROL: In ECHO mode the treadle
controls the “MIX”. The MIX adjusts the blend of the
original signal and effected signal.
REFER TO THE SAMPLE SETTINGS SECTION OF THIS
MANUAL FOR HINTS.
DIAGRAM #1
CHORUS RELATED (see diagram #2):
F. CHORUS/VIBRATO ON/OFF SWITCH: Switches
between ECHO (LED off) and CHORUS (LED on) effects.
G. CHORUS LED: Lights up when CHORUS effect is
engaged. In Chorus mode you will notice the LED blinks in
real time with the speed of the Chorus. When LED is off,
ECHO mode is active
H. CHORUS DEPTH: Controls the mix of original signal
and effected signal.
I. TREADLE CONTROL: In CHORUS mode, the treadle
controls the “SPEED”. The SPEED increases or decreases
the speed of the Chorus.
REFER TO THE SAMPLE SETTINGS SECTION OF THIS
MANUAL FOR HINTS.
DIAGRAM #2
BATTERY REPLACEMENT
When the battery becomes weak, the overall effect will
become weak and your signal may become slightly
distorted.
Remove the battery door located on the bottom of the
pedal. (a short cord is attached to the door to help prevent
loss. Once the door is off, the old battery can be removed
from the battery snap and a new battery plugged in. Make
sure the polarity (+/-) is correct before inserting the new
battery.
When you replace the battery door , you will notice it fits
very tightly against the battery. This prevents the battery
from rattling inside the pedal.
WARRANTY
All Morley® pedals are warranted for two years from date
of purchase. To obtain warranty service call
1-800-639-4668.
SPECIFICATIONS
POWER: 9 Volt Battery
CURRENT DRAW: 28 mA @ 9 VDC
WEIGHT: 3.2 lb./ 1.46 kg
INDICATORS:
LEFT LED: Effects on or Bypassed
RIGHT LED: Echo on or Chorus on.
185 Detroit Street, Cary, IL 60013
Phone: (847) 639-4646 Fax: (847) 639-4723
www.morleypedals.com