Philips CDD 882 - Manual (Page 8)

8. Press OPEN.
-The disc tray opens.
-The information disappears from the dispiay.
- The entire track number indicator iights up.
9. Take the disc from the disc tray.
10. Cióse the disc tray.
- 'Disc appears on the dispiay, indicating there is no disc on the
disc tray.
11. Press ON/OFF.
-The dispiay and the on/off indicators go out.
-The piayer is now switched off.
6B Special features during play
Short interruption of play
1. Press PAUSE.
- 'PAUSE' appears on the display.
-The music stops but the disc continues to spin.
PLAY/REPLAY, ◄◄ SEARCH. FAST. SEARCH M TRACK and
TRACK M may be used during pause to move to any particular
location.
2. Press PAUSE again to restart play from where it was
interrupted.
Stopping play
Press STOP/CM.
-The disc stops spinning.
- The display again shows the total number of tracks and total
playing time.
Returning to the beginning of the current track
Press PLAY/REPLAY.
- Play stops for a moment, then restarts at the beginning of the
track.
Moving to the next track (or any later track)
Key in the desired track number using the 1-0 digit buttons.
You can also repeatedly press TRACK W until the desired number
appears on the display.
- The music stops, 'TRACK' flashes briefly on the display and a
moment later the following track starts playing.
If there is no following track on the disc:
- 'ERROR' appears briefly on the display.
- Play continues with the current track.
Moving back to a previous track
Key in the desired track number using the 1-0 digit buttons.
You can also repeatedly press M TRACK until the desired number
appears on the display.
-The music stops, 'TRACK' flashes briefly on the display and a
moment later the following track starts playing.
If there is no previous track on the disc:
- 'ERROR' appears briefly on the display.
- Play continues with the first track.
Moving to the next (or any later) index number
Press INDEX IIH" on the remote control handset.
- Play stops for a moment, then restarts at the beginning of the
next index number (of the current track).
If the current track has no further index number:
- 'ERROR' appears briefly on the display.
- Play starts again from the first index number of the current track.
You can move forward to an index number which is further
towards the end of the track by quickly and repeatedly pressing
INDEX ....
If you want to move forward to an index number in a later track,
you must first select the required track number using TRACK W
and then the required index number using INDEX II»".
Moving back to a previous index number
Press "iill INDEX on the remote control handset.
- Play stops for a moment, then restarts at the beginning of the
previous index number.
If the current track has no earlier index number:
- 'ERROR' appears briefly on the display.
- Play starts again from the first index number of the current track.
You can move back to an index number which is closer to the
beginning of the track by quickly and repeatedly pressing
"lill INDEX.
If you want to move back to an index number in an earlier track,
you must first select the required track number using M TRACK
and then the required index number using INDEX II»".
Searching for a passage
1. Press SEARCH ^ for a forward search.
2. Press SEARCH for a reverse search.
Keep the button pressed until you reach the required piece of
music. At this searching speed the sound remains audible. This
makes it possible to find the exact passage.
If you try searching past either end of the disc:
- 'ERROR' appears briefly on the display.
If you reach the end of the disc and release SEARCH ►►, play starts
several seconds before the end.
Rapid search for a passage
1. Press FAST.
- ’FASt’ appears on the display above 'MIN' and 'SEC.
2. Press SEARCH ►► or SEARCH within 1 second.
Hold the SEARCH button pressed down; if you release the button
for a moment, search will recommence at the slowest speed.
At the fast searching speed no sound is audible. This enables you
to move quickly towards the passage you are looking for.
Repeating a disc
1. Press REPEAT.
- 'REPEAT appears on the display.
-The whole disc is repeated over and over.
2. To stop repeat, press REPEAT again.
- 'REPEAT' goes out.
- Play stops at the end of the disc.
Playing the tracks on the disc in a random order
Press SHUFFLE.
- 'SHUFFLE' appears on the display.
- If the tray is open, it will now close.
-A 'P'appears above 'MIN'; above 'SEC a two-second pause
is counted down, while an indicator above it can be seen moving.
This is repeated each time before a new track or program section
is played.
-The tracks on the disc are now played in an entirely random
order, not the order in which they appear on the disc. If there is
a program in the memory, this will be played in a random order,
not corresponding to the order in the program.
If you also press REPEAT, the disc will be played repeatedly and
each time all tracks will be played in a different random order.
During playback in random order, you can use the M TRACK W
buttons.
Setting up a continuous play loop
While a disc or program is playing you can set up a continuous
play loop.
1. During play, press A-»B at the required start point.
- 'A-»-B' starts flashing on the display.
- The start point of the play loop is set.
2. Press A-^B again at the required stop point.
- 'A->B' lights up continuously.
- The stop point of the play loop is set.
-The laser pick-up immediately moves back to point A and
everything between this point and point B will now be played. The
laser pick-up then returns to point A and so on.