Futaba MC601C User Manual
Mc601c, Nstruction anual

MOUNTING PRECAUTIONS
Accessories
s
(EATSHRINK
s
)NSTALL
-ETAl
Alw
AYS
NOT
If
LOST
)NSERT
If
MAY
$O
If
CONTROL
Alw
AYS
ON:
OFF:
If
MAY
7HEN
If
START
Alw
AYS
7HEN
EHICLE
7HEN
MC601C
NSTRUCTION
ANUAL
-.
Serial communication function (Options)
The following settings and operations are possible with a Windows PC by using the optional interface unit (CIU-2).
*Windows is registered trademark of Microsoft Corporation.
"EfORE
s
WITHOUT
s
PRIOR
s
&UTABA
Thank you for purchasing an MC601C . The MC601C is a high-frequency drive FET speed control developed for model
electric cars. It is compact and light weight competition speed control, and uses a simple digital setting system.
Applicable motors
.UMBER
Use the MC601C with a motor with 9 turns or more.
*If a motor with a number of turns smaller than the
above is used, the heat protector and overcurrent
protection circuit may operate. The number of turns of
the motor is a criteria only. Depending on the running
conditions, the protection circuit may operate even if
the condition above is satisfied.
*The internal circuit of MC601C is OK up to 9-turn
motors. On the other hand, the connectors for battery
and motor are general type that is often found at the
dealers. Therefore, to use high output power motor or
apply heavy load may result in overheating of the
connector section and melting the connection. If this
happen the connection will stick together. Please pay
special attention to avoid this matter.
Power supply
Nicd, NiMH battery 4~7 cells
(4.8~8.4V)
FEATURES
• SMD MOSFETs with smallest internal resistance for
minimal losses and maximum power
•
PWM frequency is Performed by load adaptive
•
Heat protector
•
Low-voltage protection function
•
Fuse 40A
(Buttery reverse plotection / Overload plotection)
•
Power left on alarm function
•
Serial communication function
INSTALLATION TIPS
s
lectronic components.
s
Important:
s%NSURE that there is an adequate distance (approx. 3 cm) between the speed control and power cables and the receiver or receiver antenna. Avoid
direct contact between all power system components and the receiver or antenna, as this can cause interference. If you encounter interference
problems, re-position the components in the model.
s4HE antenna should be run vertically up and away from the receiver. Avoid contact with any parts made of carbon fibre or metal. See also the
instructions supplied with your radio control system.
[MC601C Technical Data]
3PECIFICATIONS
s Operating system: Forward and brake (resolution:255)
s Power requirement: Nicd, NiMH battery 4~7 cells (4.8~8.4V)
s PWM frequency:
Forward 100Hz
10kHz
Initial value 2.5kHz
3.0kHz
Brake 2.0kHz
s BEC voltage: 6.0V (excluding at less than 6V)
s Setting: One-touch input by pushbutton switch.
s Current capacity (FET rating) :
Forward
480A (Momentary load: 1920A)
Brake
120A
s Fuse: 40A (Buttery reverse plotection / Overload plotection)
s Case size: 28.7x26.2x13.3mm (excluding protruding parts)
s Silicon cord gauge size: AWG14 equivalent
s Weight: 13.5g (excluding connector, cords and switch)
$O
)T
$O
4HE
N
EvER
2EvERSE
-OUNT
!
If
OR
EHICLE
F
ORCEFULLY
$O
T
OUCHING
SERIOUS
If
RUN
4HIS
T
URN
FLOATED
7HEN
MOUNTING PRECAUTIONS
Special Markings
Pay special attention to the
safety at the parts of this
manual that are indicated by
the following marks.
Mark
Meaning
0ROCEDURES
0ROCEDURES
0ROCEDURES
Symbol:
0ROHIBITED
-ANDATORY
s
approximately 8 minutes at 1 second intervals.)
s Variable frequency range setting: 100Hz ~ 10kHz (Sets the load response system variable frequency range.) Dead
band: ±2μs ~ ±55μs (The neutral point range can be set.)
s Low battery protection voltage setting: 2.5V ~ 6.0V (Sets thevoltage which cuts output to motor when the power supply
voltage is drops.)
s
MC601C
MC601C