Futaba R6203SBE - Manual (Page 2)

What is S.BUS?
Different from conventional radio control systems the
S.BUS
system uses data communication to transmit control signals
from a receiver to a servo, gyro, or other
S.BUS compatible
device. This data includes commands such as “move the
channel 3 servo to 15 degrees, move the channel 5 servo to
30 degrees” to multiple devices. The
S.BUS devices execute
only those commands for their own set channel. For this
reason, it can be used by connecting multiple servos to the
same signal line.
[Connection by S.BUS system]
S.BUS hub S.BUS hub
S.BUS output
S.BUS
Ch output/
Battery terminal
R6203SBE
Battery
S.BUS servo
Conventional
servo
2ch 4ch
3ch 5ch
6ch
* Set the channel at the S.BUS
* &DQ DOVR EH XVHG WRJHWKHU ZLWK FRQYHQWLRQDO VHUYRV +RZHYHU FRQYHQWLRQDO VHUYRV FDQQRW EH XVHG E\ WKH S.BUS RXWSXW
* :KHQ XVLQJ VHUYRV ZLWK D UHPRWH EDWWHU\ SDFN XVH S.BUS +XE ZLWK &DEOH ZD\UHPRWH EDWWHU\ SDFN XVH
3OHDVH UHIHU WR WKH LQVWUXFWLRQ PDQXDO RI S.BUS +XE ZLWK &DEOH ZD\UHPRWH EDWWHU\ SDFN XVH IRU WKH FRQQHFWLRQ PHWKRG
Operation Mode Select
The operation mode is on "Normal mode" from factory
shipping. When to change the mode, please follow the steps
shown below.
1
2
THE
STATUS
3
4
By doing this step, the mode can switch over between two(2)
modes.
0 to 1 sec. More than 1 sec.
0 sec. 1 sec.
Press and Hold
Turn on the receiver.
No function
Showing the CURRENT
mode with blink.
Red Blink = Normal
Green/Red Blink =
High Speed
Solid as the mode changed.
Red Solid = Normal
Green/Red Solid = High
Speed
(Become Red after one (1)
second)
㸦Function㸧
To change the mode between
Normal and High Speed
㸦LED Status㸧
Please check the operation mode by observing the
LED when
turning on the receiver. If possible there's no
FASST transmitter
WXUQHG RQ DURXQG \RX LQ RUGHU WR PDNH ¿UPHU FKHFN
When turn on the receiver, the
LED will be;
s
!FTER
If there are some
FASST transmitter turned on around the
receiver, the
LED may show the above status for a brief
moment then changed to the status indication as shown in the
"
LED indication" table.
 WARNING
 $O
MOTORgS
IN
￸ 7HILE
POWER
REALLY
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
‹)87$%$ &25325$7,21
LED Indication
'REEN 2ED 3TATUS
Solid Solid )NITIALIZING
Off Solid No signal reception
Solid Off 2ECEIVING
Blink Off 2ECEIVING
Alternate blink 5NRECOVERABLE
Link to the transmitter
1
TWO
Re-adjust the F/S position (only for TM-8)
1
AND
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Other than TM-8
(not included in this set)
Re-link(ID set)