Emerson Radio CKS9031 Part 2 User Manual
Am mon tue wed thu fri sat sun
12
8
9
Selecting The Alarm Mode
Your SmartSet
®
clock radio allows you to select from among three different alarm
operation modes for either alarm. The alarm modes are:
•
Everyday – The alarm will turn on all 7 days.
•
Weekdays only – The alarm will only turn on Monday through Friday;
•
Weekends only – The alarm will only turn on Saturday and Sunday.
To check the Alarm Mode setting for Alarm 1, depress the
ALARM 1 setting button.
The display will show theAlarm 1 wake up time and the “Day Of The Week” indicators
will show you the alarm mode which is selected.
Release the
ALARM MODE and ALARM 1 setting buttons and the display will
return to the correct time.
Follow the same procedure to select the desired Alarm Mode for Alarm 2 if
necessary.
To change the Alarm Mode setting for Alarm 1, hold the
ALARM 1 setting button
and press the
ALARM MODE button until the Day indicators show the desired
mode setting, Weekdays only, Weekends only, or Everyday operation.
• If all 7 indicators are ‘On’, the Everyday mode
is selected.
• If only the Monday through Friday indicators are
‘On’, the Weekdays only mode is selected.
• If only the Saturday and Sunday indicators are
‘On’, the Weekends only mode is selected.
Checking The Wake Up Times And Alarm Mode
Whenever you want to check the wake up time or the alarm mode settings, simply
press either the
ALARM 1 or ALARM 2 setting buttons. The display will change
from correct time to wake up time and the day indicators will show you the alarm
mode which is currently selected.
Release the
ALARM 1 or ALARM 2 setting buttons to return to correct time.
13
15
11
10
14
AM
MON TUE WED THU
FRI
SAT
SUN
ALARM
ALARM
ALARM
ALARM
ALARM 1
ALARM 2
CR2032
CR2032
Tuesday
2008
CKS9051/CKS9031
CKS9051/CKS9031-902-02
twice
“ ”
“ ”
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020 OR
1-800-695-0098 OR
E-MAIL TO: [email protected]
Send your unit to:
Emerson Returns Facility
11500 Philadelphia ST
Mira Loma, CA 91752
ATTN:Returns Department
AM
MON TUE WED THU
FRI
SAT
SUN
AM
MON TUE WED THU
FRI
AM
SAT
SUN
Listening To The Radio
Digital Radio Frequency Display
1.) Set the
Band AM/FM selector switch to the desired band, AM or FM.
2.) Set the
VOLUME control to a low setting.
3.) Press the
RADIO ON/OFF button to turn the radio ‘On’. The display changes
from time to an
AM or FM radio frequency display.
4.) Turn the
TUNING control to the leftside to select higher numbered
frequencies or to the right-side to select lower numbered frequencies.
to the clock radio
AUX IN jack with a cable with 2 ends 3.5mm stereo plug.
3.) “
AUX IN” indicator will light on while AUX IN jack is plugged in, and the radio
will change to AUX function.
4.) Start to play iPod,MP3 or other audio player, and set the player volume to
maximum.
5.) Adjust the main unit volume to your desired level.
6.) Stop the main unit and your iPod, MP3 or other audio player when finished
listening, and disconnect the cable from the
AUX IN jack.
Remark:
Once the
AUX IN jack is plugged in,the alarm sound will be buzzer sound only
while the alarm function is activated.
5.) Adjust the
VOLUME control to the desired setting.
6.) When you are finished listening, press the
RADIO ON/OFF button to turn
the radio ‘Off’.
Important: It is not necessary to tune to the exact frequency of your desired
station. Just rotate the TUNING control until you find the strongest signal and
the best reception, even if the frequency number on the display is higher or
lower than the actual station frequency.
3.) Set the
ALARM selector switch for one or both alarms to the “RADIO”
position The appropriate
ALARM 1 and/or ALARM 2 indicators will light up
to confirm that the alarms are set.
CR2032
AU898N