Casablanca Fan Company Casablanca Ceiling Fan 6643050 - Manual (Page 16)

16
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth
should be used to prevent scratching the fi nish. A vacuum cleaner
brush nozzle can remove heavier dust. Surface smudges or an ac-
cumulation of dirt and dust can easily be removed by using a mild
detergent and slightly dampened soft cloth. An antistatic agent
may be used, but
never use abrasive cleaning agents. These will
damage the fi nish. Painted and high-gloss blades may be cleaned
in the same manner.
Blades: Wood fi nish blades should be cleaned with a furniture
polishing cloth. Occasionally, a light coat of furniture polish may
be applied for added protection and beauty.
Never Lubricate this Fan!
The precision motor at the heart of your Casablanca fan features
sealed bearings that are lubricated for life. Do not attempt to oil
the motor.
Changing Light Bulbs
Be sure to turn power to the fan OFF at the wall switch or circuit
breaker before changing light bulbs. Replace bulbs with same type as
removed from the fi xture. Each fan is rated for a
maximum TOTAL
wattage of lighting.
Exceeding the rated maximum allowable wattage for the fan will
burn out the fan electronics module and void the warranty.
PROB- POSSIBLE REM-
PROBLEM POSSIBLE REMEDIES ..
FAN WILL NOT START -Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
-Pin connectors are not making good contact. Check all connections.
-Battery weak—install fresh battery.
-Fan receiver defective—replace.
FAN DOES NOT RESPOND -Power to fan is off.
TO REMOTE CONTROL -Wrong remote is being used.
-Remote dip settings changed—see instructions for changing the frequency setting.
FAN WOBBLES OR SHAKES -Be sure canopy pin is properly set into the slot on the ball.
EXCESSIVELY -Check that bladeholders have not been bent during installation and blades are balanced.
-Hanger bracket and/or ceiling outlet are loosely attached: Make sure that the hanger bracket is tightly
attached to the ceiling outlet box. Make sure that the downrod assembly is secured fi rmly.
-Downrod is loosely attached to downrod base: Make sure that all screws are securely tightened.
FAN NOISY DURING -Check and tighten light fi xture retaining screws, glass shade screws and/or the light bulb(s).
OPERATION -Tighten canopy screws and mounting plate assembly. Check that the wire nuts inside the canopy and
switch housing are not touching the metal parts or have fallen off the wire splices. Tighten as necessary.
-Tighten blade holders to fl ywheel (or direct drive motor)/and blade to bladeholder screws.
-Make sure all screws in the motor housing are snug, but not overly tight. Defective bulb: Replace bulb.
DOES NOT RUN ON -If new, “break-in” may be required - run at higher speed for several days.
LOW SPEED
BATTERY LIFE -Not using Alkaline batteries: Replace with ALKALINE batteries.
SEEMS SHORT
ADVAN•TOUCH
FAN O.K., NO LIGHT: Check for burned out light bulb. Check fan light wires.
LIGHT O.K., NO FAN: Check connectors, may not be making good contact.
REMOTE CONTROL OF FAN IS ERRATIC: Check batteries installed correctly. Install fresh ALKALINE batteries.
FAN STARTS WORKING BY ITSELF: Frequency interference; Change dip switch code.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inter-
ference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equip-
ment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for
help. Note: Any changes or modifi cations to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority
to operate this remote control.
A
DVAN
•T
OUCH
™