Pioneer DE-UH9101 - Manual (Page 4)

[ Connecting a Daisy Chain Configuration ]
This unit uses a SCSI interface. A daisy chain configuration enables
connection of a maximum of 8 SCSI devices.
(1) Set SCSI ID using bit 1 - 3 of jumper terminals ® (see
figure below),
(2) Bit 9 of jumper terminals ® shall be OFF, only when the
unit is the last SCSI device on the daisy chain..
NOTE:
e Make sure the overall length of the SCSI cable does not exceed 6
meters (The SCSI cable 1$ sold separately.)
o Be sure not to duplicate the SCSI ID.
{Setting Jumper Terminals Ф]
@ SCSI ID (bits 1 to 3)
Sets this unit's SCSI ID (see figure below),.
(g) Parity check (bit 4)
Determines whether to perform the SCSI data bus parity check..
Performs parity check when OFF.
© Bits 5, 6 are reserved Shaii be set to OFF,
® Mode swiichirig (ШОЕ, bits 7, 8)-
-
Determines the operation mode after reading the bits following
power-on or SCSI RESET
e MODE 0; Rewritable mode
о MODE 1: WORM mode
e MODE 2: SCSI-2 mode
« MODE 3: Reserved
' Mode can also be selected by an SCSI command
Ф SCSI terminator (bit 9)
Determines whether or not the unit’s SCSI terminator is to be
used
ìOH^ii^ÌcàteslthÌt:SGSÌ5timiÌnà№ié;tob(^^
NOTE;
0 All settings are in the OFF at the time of shipment from the factory
When setting to the ON, insert the supplied jumper pin.
0 Use the factory setting (OFF) for bits 4 - 6 except
o Be sure not to lose the jumper pin. When switched OFF, it is conve­
nient to leave one side only connected
0 When setting with an external switch, remove all jumper pins, and
transmit the signals using a 2 54 mm pitch 2-line 18-pin connector
[ Specifications ]
e Interface
о Rotational speed
0 Bit error rate
a Dimensions
a Weight
a Power supply conditions*^
a Available positioning
a Environmental conditions
Operating temperature
Operating humidity
Storage temperature
Storage humidity
SCSI-2*’
2700rpm, ZCAV (when a DEO-17GMO
or DC-17GWO is used)
2400rpm, CAV (when a DEC-702
or DC-502A is used)
Less than 10-’^ (when a PIONEER op­
tical disk is used)
Refer to the figure on P. 16 for
dimensions,
1,4kg (3ib, 1 oz)
-i-5 V, 1 „2 A typ, 2,5 A max
+12 V, 0,6 A typ, 2,5 A max
Horizontal or vertical
+5'C - +40“C (+41”F - +104“F)
10% ~ 80% RH
(no condensation)
~20^C - +50°C (-4T ~ +122T)
10% ~ 90%RH
(no condensation)
□ □ □ □ □
t 3 □ {
3 0 i
3 n [
3 a {
3 a
'i a n
a ij q.
bit
SCSI ID
Parity check
Reserved
Reserved
Mode switching
1 2 3 4 5 6 7 8 9
V
Ф Jumper
Terminals
Internal SCSI terminator
VON ; not used
GN when the jumper pin is connected, OPi when
removed.
SCSI ID biti bit 2 bits
0 OFF OFF OFF
1 ON OFF OFF
2 OFF ON OFF
3 ON ON OFF
4 OFF OFF ON
5 ON OFF ON
6 OFF ON ON
7 ON ON ON
MODE bit? bite
0 OFF OFF
1 ON OFF
2 OFF ON
3 ON ON
[ Changer interface and spindle control interface ]
This unit is equipped with a changer interface for connecting to an
auto changer controller when it is incorporated in an auto changer,
and with a spindle control interface for synchronous operation of sev­
eral drives. Interface specifications are available upon request,
0 Accessories
Manual eject screwdriver ............................................................ 1
Jumper pin....................................................................................... 9
Operating instructions................................................................ 1
*1 SCSI,. ......................................... Small Computer System Interface
‘2 The typical value is the value when the drive is not executing a
command
NOTE:
Specifications and design subject to passible modifications without
notice, due to improvements
Publtshed by Pioneer Eiectiic Corporaiion
Copyrigh! c 1994 Pioneer Sioctronic Corporation
All rights reserved
6
En