Kenmore 251.50701 - Manual (Page 5)

CONTROL PANEL 50351 (U.S.), 25011 (CANADA) CONTROL PANEL 50501/50701 (U.S.), 25013/25014 (CANADA)
f) ® (D
POWER ON/OFF(1)
Pressing Power button once turns the
dehumidifier “ON” and pressing it again
turns the dehumidifier “OFF.”
Setting (2)
By pressing this button, unit will cycle through
each setting with every press. The order of
settings are Humidity - Cycle Timer - Delay
Start - Humidity ...
Humidity (9)
When the unit is turned on, the unit will default
to Humidity mode. In this setting. Humidity
allows you to manually set the desired humidity
level by using the humidity arrow or key (4/5).
Humidity values are changed in 5% increments
ranging from 35% to 70%. Humidity is shown
in window (8). When pressing v arrow key
when the value is 35%, the unit will operate
continuously. In this continuous operation, Lo
will be displayed in the window (8). To leave
continuous operation, press the arrow up or
change the setting.
Cycle Timer Setting (10)
In this setting, the unit will run for
either 3, 6, or 12 hours, then shut off for 3, 6,
or 12 hours. Cycle time can be adjusted by
pushing the timer arrow up or down (4/5)
repeatedly to set operating time for 3, 6, or
12 hours. The cycle timer function will continue
until you change the setting or turn the unit off.
Delay Start (11)
Unit can be programmed to turn on at a desired
delay time by pushing the timer arrow and key
(4/5). Time can be adjusted in 1 hour increments
ranging from 1 to 12 hours. Delay time will be
shown in window (8) and will count down to
start time in 1 hour increments.
FAN SPEED (3)
Press Fan Speed to toggle between Low and
High fan speeds. Speed will be shown in
FAN SPEED INDICATOR (6).
BUCKET FULL INDICATOR (7).
When the collection bucket is full, BUCKET FULL
indicator (7) will come on. The dehumidifier will
not run until the bucket is empty.
IMPORTANT:
When the unit is turned off and restarted, the
unit will operate at the previous operation
setting.
NOTICE:
A power failure will require the unit to be turned
back on manually and adjusted to the desired
setting.
(3) (i)
POWER ON/OFF(1)
Pressing Power button once turns the
dehumidifier “ON” and pressing it again turns
the dehumidifier “OFF.”
Setting (2)
By pressing this button, unit will cycle through
each setting with every press. The order of
settings are Auto - Humidity - Cycle Timer-
Delay Start - Auto ...
Auto (9)
When the unit is turned on, the unit will default
to Auto mode. AUTO (9) and “50%” humidity
value will be displayed in window (8). In this
setting, humidity level is automatically set for
50% RH. Because lower temperatures usually
correlate with lower humidity levels, the unit will
not run frequently. At higher temperatures higher
humidity is normal so the unit will run more often.
Humidity (9)
In this setting. Humidity allows you to manually set
the desired humidity level by using the humidity
V arrow or key (4/5). Humidity values are changed
in 5% increments ranging from 35% to 70%.
Humidity is shown in window (8). When pressing
arrow key when the value is 35%, the unit will operate
continuously. In this continuous operation, Lo will
be displayed in the window (8). To leave contin­
uous operation, press the arrow up or change the
setting.
© @
Cycle Timer Setting (10)
In this setting, the unit will run for either 3, 6,
or 12 hours, then shut off for 3, 6, or 12 hours.
Cycle time can be adjusted by pushing the
timer arrow up or down (4/5) repeatedly to set
operating time for 3, 6, or 12 hours. The cycle
timer function will continue until you change
the setting or turn the unit off.
Delay Start (11)
Unit can be programmed to turn on at a desired
delay time by pushing the timer arrow and key
(4/5). Time can be adjusted in 1 hour increments
ranging from 1 to 12 hours. Delay time will be
shown in window (8) and will count down to
start time in 1 hour increments.
FAN SPEED (3)
Press Fan Speed to toggle between Auto, Low,
and High fan speeds. Speed will be shown in
FAN SPEED INDICATOR (6). When AUTO is
selected, the unit will adjust the fan speed
accordingly depending on the humidity level.
BUCKET FULL INDICATOR (7)
When the collection bucket is full, BUCKET
FULL indicator (7) will come on. The dehumidifier
will not run until the bucket is empty.
IMPORTANT:
When the unit is turned off and restarted, the
unit will operate at the previous operation
setting.
NOTICE:
A power failure will require the unit to be turned
back on manually and adjusted to the desired
setting.