Ryobi RY39505 - Manual (Page 13)

11 - English
CLEANING THE HEDGE TRIMMER
 Stop the engine and disconnect the spark plug wire.
 Slide the scabbard over the blade.
 Clean dirt and debris from the body of the hedge trimmer,
using a damp cloth with a mild detergent.
NOTE: Do not use any strong detergents on the plastic
housing or the handle. They can be damaged by certain
aromatic lubricants such as pine and lemon, and by sol-
vents such as kerosene.
CLEANING THE AIR FILTER SCREEN
See Figures 9 - 10.
For proper performance and long life, keep air filter clean.

Remove the air filter cover by pushing down on the latch
with your thumb while gently pulling on the cover.
 Brush the air filter screen lightly to clean.
 Replace the air filter cover by inserting the tabs on the
bottom of the cover into the slots on the air filter base;
push the cover up until it latches securely in place.
NOTE: For best performance, replace annually.
FUEL CAP, TANK, AND LINES
WARNING:
Check for fuel leaks. A leaking fuel cap, tank, or lines is a
fire hazard and must be replaced immediately. If you find
any leaks, correct the problem before using the product.
Failure to do so could result in a fire that could cause
serious personal injury.
The fuel cap contains a non-serviceable filter and a check
valve. A clogged filter or faulty check valve will cause poor
engine performance. Replace fuel cap if required.
IDLE SPEED ADJUSTMENT
See Figure 11.
WARNING:
The blades will move when adjusting the idle speed. Wear
all protective clothing and keep all bystanders, children,
and pets at least 50 ft. away. Make adjustments with
the unit supported by hand so that the blades do not
contact the ground or any object. Keep all parts of your
body away from the blades and muffler. Failure to follow
these instructions could result in serious personal injury.
If the blades move at idle, the idle speed screw needs adjust-
ing on the engine. Turn the idle speed screw counterclockwise
to reduce the idle RPM and stop the blade movement. If the
blades still move at idle speed, contact a service dealer for
adjustment and discontinue use until the repair is made.
MAINTENANCE
WARNING:
The blades should never move at idle. Turn the idle speed
screw counterclockwise to reduce the idle RPM and stop
the blades, or contact a service dealer for adjustment and
discontinue use until the repair is made. Serious personal
injury could result from the blades turning at idle.
SPARK PLUG REPLACEMENT
This engine uses a Ryobi AC00160 or Champion RCJ6Y
with .025 in. electrode gap. Use an exact replacement and
replace annually.
CLEANING THE EXHAUST PORT, MUFFLER,
AND SPARK ARRESTOR
NOTE: Depending on the type of fuel used, the type and
amount of lubricant used, and/or your operating conditions, the
exhaust port, muffler, and/or spark arrestor screen may
become blocked with carbon deposits. If you notice a power
loss with your gas powered tool, you may need to remove
these deposits to restore performance. We highly recommend
that only qualified service technicians perform this service.
The spark arrestor must be cleaned or replaced every 50
hours or yearly to ensure proper performance of your product.
Spark arrestors may be in different locations depending on
the model purchased. Please contact your nearest service
dealer for the location of the spark arrestor for your model.
STORING THE PRODUCT
 Clean all foreign material from the product. Store idle unit
indoors in a dry, well-ventilated area that is inaccessible
to children. Keep away from corrosive agents such as
garden chemicals and de-icing salts.
 Abide by all ISO and local regulations for the safe storage
and handling of gasoline.
When storing 1 month or longer:

Drain all fuel from tank into a container approved for
gasoline. Run engine until it stops.
HIGH ALTITUDE ENGINE OPERATION
Please have an authorized service center adjust this engine
if it is to be run above 2000 feet. Failure to do so may result
in poor engine performance and increased emissions. An
engine adjusted for high altitudes can not be run at 2000
feet or lower. In doing so, the engine will overheat and cause
serious engine damage. Please have an authorized service
center restore high altitude modified engines to the original
factory specification before operating below 2000 feet.