Symtech Gold Series Kit - Manual

BRIGHT SOLUTIONS
Gold Series
HEADLAMP Resurfacer / Protector
Thank you for purchasing BRIGHT SOLUTIONS, Gold Series
this is a 3 or 4 STEP process that takes approximately 10~15
MINUTES to perform per headlamp dependent upon severity of
damage of lamp lens. By applying the patented Preserver, your
headlamp restoration will be preserved for more than two years.
KEEP OUT OF THE REACH OF CHILDREN
DO NOT ALLOW PRODUCT TO FREEZE
WHEN APPLYING PRODUCT IN TEMPERATURES
BELOW 60 o , TURN LAMPS ON UNTIL WARM.
DO NOT APPLY SHINE RESTORER/ PROTECTOR IN
DIRECT SUNLIGHT
READ INSTRUCTIONS IN ENTIRETY BEFORE USE.
USE GLOVES TO PROTECT HANDS.
RECOMMENDED
524 S.E. Transport Drive
Lee’s Summit, Missouri 64081
816-525-9263 FAX: 816-525-9383
www.symtechcorp.net
Safety by Design
SAFETY and HEALTH
WARNINGS
ALL PRODUCTS INCLUDED IN THIS KIT ARE ON
REVERSE SIDE
A
s with any repair versus replacement, some items will not
achieve like new results. If directions are followed, significant
improvement in the appearance of the items will be achieved. As
we are unable to supervise the application process, user assumes all
risks. The manufacturer and its distributors are not liable for any
damages incurred by the use of this product. If you are unsure as
to the application process or compatibility of the item you would
like to resurface, please contact the manufacturer or distributor for
advice on how to proceed.
Can Be Used on : Headlamps Taillights
Turn Signal Lights Reflective Lens Covers
FIRST determine the extent of damage that has occurred over time to
your headlamp lens.
IF Headlamp lens is slightly fogged and or yellowed, without
visible hairline scratches or crazing, in most cases, the lamp
can be simply cleaned clear without the use of sandpaper.
Steps 1, 3 and 4
IF Headlamp lens has extensive yellowing, scratches, crazing
and/or pits, sanding is necessary to obtain a successful
result. Regardless of damage, using sandpaper during
cleaning will speed the process dramatically.
Steps 1, 2 ,3
STEP 1
CLEANING
Select a paper shop towel and fold in quarters (1).
Thoroughly shake the BRIGHT SOLUTIONS Pretreatment
before applying to towel.
Open the specially formulated BRIGHT SOLUTIONS
Pretreatment, saturate the towel (2), and begin cleaning the
entire lens with a circular motion (3).
Continue cleaning, changing the towel surface and adding more
Pretreatment as towel becomes discolored (4) with dirt and
oxidation film of lamp lens.
When dirt and discoloring ceases to be removed from lens, Proceed to
STEP 2 or 3 .
STEP 2
SANDING
Fill a container, or spray bottle with water (5), start with 1500 grit
sandpaper, dampen with water and begin sanding the entire
surface of the lens, wetting sandpaper (6), or lens as needed to
prevent buildup of particles. Sanding is complete when lamp
lens is uniform in appearance.
Note: ALWAYS sand in a straight motion (7), DO NOT use
a circular motion.
Continue sanding until all discolored plastic has been removed from
lamp surface and residue of sanding is white in appearance.
Take the 2000 grit sandpaper, dampen with water and sand the entire
surface of the lens, wetting sandpaper (6) as needed. This
process will reduce the sanding lines .
Note: ALWAYS sand in the same direction as previous step
and in a straight motion (7), DO NOT use a circular
motion.
STEP 4
SHINE RESTORER/PRESERVER
Select a LINT-FREE paper shop towel and fold in quarters (1).
NOTE: Apply SHINE RESTORER/ PROTECTOR out
of direct sunlight. WHEN APPLYING PRODUCT
IN TEMPERATURES BELOW 60
o , TURN LAMPS
ON UNTIL WARM
Apply a liberal amount of the SHINE RESTORER/
PROTECTOR to a clean lint-free paper towel (8) and apply it
smoothly across the plastic surface (9), avoiding runs and
bubbling. Do not wipe till dry or tacky, wipe on wet, stand back
and let dry
To remove SHINE RESTORER/PROTECTOR from other
surfaces when wet, rinse with water and wipe off with a dry
towel.
Multiple coats of SHINE RESTORER/PROTECTOR are
recommended to increase the shine and protection properties.
Plastic surface must be dry to the touch prior to each application of
additional coats.
2
8
4
1
Five Minutes
Drying Time
7
3
5 6
9
Select a paper shop towel and fold in quarters (1).
Thoroughly shake the BRIGHT SOLUTIONS HEADLAMP
CLEANER/POLISH before applying to towel. Shake the
container frequently throughout the cleaning process.
Open the specially formulated BRIGHT SOLUTIONS
HEADLAMP CLEANER/POLISH, saturate a small area of
the towel (2), and begin cleaning the entire lens with a circular
motion (3).
Continue polishing and adding more HEADLAMP CLEANER/
POLISH as necessary to polish the entire lamp lens.
When lens has achieved a highly polished appearance, wipe off all
polish residue with Pretreatment
Proceed to STEP 4 .
STEP 3
POLISHING