Pridiom Elite Series PWS247EL Remote Control Manual - Manual (Page 4)

5 5 6 6
FP/EYE Button
TIMER ON Button
TIMER OFF Button
UP Button( )
Push this button to decrease the indoor
o o temperature setting in 1 F increments to 62 F.
DOWN Button( )
9
11
12
10
Press this button to initiate the auto-on time
sequence. Each press will increase the auto-
timed setting in 30 minutes increments. When
the setting time displays 10, each press will
increase the auto-timed setting 60 minutes
increments. To cancel the auto-timed program,
simply adjust the auto-on time to 0.0.
Press this button to initiate the auto-off time
sequence. Each press will increase the auto-
timed setting in 30 minutes increments. When
the setting time displays 10, each press will
increase the auto-timed setting 60 minutes
increments. To cancel the auto-timed program,
simply adjust the auto-off time to 0.0
Push this button to increase the indoor
o o temperature setting in 1 F increments to 86 F.
1
1
2
2
4
4 5
5
3
3
9
9
10
10
8
8
6
6 7
7
11
11
12
12
13
13 14
14 15
15
ON/OFF
ON/OFF
MODE
MODE
FAN/SLC
FAN/SLC
TEMP
TEMP
FP/EYE
FP/EYE
TIMER ON
TIMER ON
TIMER OFF
TIMER OFF
SLEEP FRESH
SLEEP FRESH
LED FOLLOW ME
LED FOLLOW ME
TURBO SELF CLEAN
TURBO SELF CLEAN
keeping on for 2 seconds, and then be off for
2 seconds by turns. Press ON/OFF,SLEEP,
FP, MODE, FAN SPEED,UP, DOWN button
while operating will cancel the freeze
protection function.
Under Intelligent eye function, with the
built-in infrared sensor, the unit can detects
existence of humans in the room. If the unit
keep detecting no human activity for 30 min,
it will automatically enters standby(monitor)
status in order to save electricity. And the
unit will automatically start and resume
operation if sensing human activity again.
Active/Disable freeze protection function. If
pushing more than 2 seconds, the Intelligent
eye function will be activated, pushing more
than 2 seconds again to disable.
During the heating operation(only when the
setting mode is HEAT),If pushing this button
more than 2 seconds, the freeze protection
function is activated. The unit will operate at
high fan speed with the temperature automa-
O tically set to 8 C. The display window of indoor
unit will display FP . For the unit without
display area, the Defrost indicator light will be
, ,
8
6
7 SELF CLEAN Button
Active/Disable Self Clean function. For details,
please see Special functions in USER S
MANUAL.
TURBO Button
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset
temperature at cooling or heating operation in
the shortest time(if the indoor unit does not
support this function, there is no corresponding
operation happened when pressing this button.)
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
, , , , , ,,
,,
NOTE: Press and hold and
buttons together for 3 seconds will alternate
O O the temperature display between the C & F
scale.
13 Swing Button
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. And the temperature display
area of indoor unit displays for one
second. If keep pushing more than 2 seconds,
the vertical louver swing feature is activated.
And the display area of indoor unit displays
, flashes four times, then the tempera- IIII
ture setting reverts back. If the vertical louver
swing feature is stopped, it displays LC and
remains on for 3 seconds.
,
,
,
,
,
,