Dyras PB-420G - Manual (Page 4)

Direct and indirect heat (e.g. being too close to an oven or a heating appliance) can cause:
- damage, deformation, softening or melting of plastic or rubber parts and casing elements, or
deterioration of electrical insulation.
Following the operating instructions and avoiding any of the conditions listed above will help you
increase the lifespan of the appliance. The manufacturer is not responsible if the appliance is stored
inappropriately or contrary to these instructions. You are recommended to have the appliance
serviced regularly by an authorised engineer to keep it working for as long as possible.
Please respect the environment when the appliance reaches the end of its life. Electrical products
must not be disposed of with other residential waste because they can damage the natural world
and may be hazardous to human health. You should dispose of the appliance at an appropriate
recycling site or by using a collection service that specialises in electrical appliances.
Please keep this instruction manual. If you give the appliance to anyone else,
you must give them this instruction manual, too!
MAIN COMPONENTS
1. Blender funnel (seal)
2. Blender
lid
3. Blender jar
4. Blender blade
5. Motor unit
6. Speed button
7. ‘Pulse’ button
8. ‘ Auto Clean’ button
9. Network
cable
10. Network switch (0/1)
11. Grinding
jug
12. Grinding blade
13. Grinding housing
POWER SUPPLY
The appliance must only be connected to mains electricity of 230V and 50Hz.
Always ensure the mains voltage where you’re using the appliance corresponds
to the value shown on the nameplate of the appliance.
EN
PB-420G
7
• Do not lengthen or alter the mains cable of the appliance. If you need a longer cable between the appliance
and the wall socket, you should buy a standard extension cord from an electrical dealer. When using an
extension cord, be careful not to create a hazard that you or someone else could trip over.
• Warning! Disassembling the appliance, opening the casing or attempting to repair it at home are forbidden -
non compliance with this instruction might result in serious accidents. The inside of the appliance does not
contain any parts that can be repaired at home or used for any other purpose. Never use the appliance with
damaged power cable or connector, if operation is erratic or if it was dropped and is otherwise damaged. If
the appliance has become faulty for any reason or moisture has got inside the casing, take it to an authorised
service engineer for checking or repair. Only skilled experts are authorised to repair the appliance. The
manufacturer is not liable for damages if home repair has been attempted or the instructions in the operating
manual have not been complied with.
Dear Customer,
All electrical and mechanical equipment needs to be cared for appropriately. It’s important to note
that using or storing the appliance in certain conditions may adversely affect its lifespan and
functionality. Always protect the appliance from the conditions listed below.
Using or storing the appliance in a wet, humid or damp environment can cause:
- deterioration and premature aging of the cover and electric insulation of the appliance,
- premature wearing and aging of the plastic and rubber components,
- rust and corrosion affecting electrical components and metal parts.
Using the appliance in a dusty environment or in the kitchen (where the air may be contaminated
with vapours from cooking oil or grease) can cause:
- greasy dust coatings on the mechanical and electrical elements and the casing of the appliance,
which could result in electrical contact failure or even complete breakdown, and could also
damage the plastic and rubber elements.
The effects of direct sunlight on the appliance can include:
- accelerated deterioration of the appliance casing and its plastic and rubber components,
damage to strength and other structural features. The appliance's surface may become porous
and fragile, which may result in a safety risk.
Continuous heavy duty use may cause:
- premature structural wear and tear and premature aging of the motor due to extensive use of
the appliance, resulting from wear and tear and overheating due to continuous use.
Storing the appliance in cold or frosty environment may cause:
- damage to the plastic and rubber components; if they become fragile,
this may result in a safety risk.
- oxidation resulting from condensation, and corrosion of the metal components.
PB-420G
6
User'sManual for PB-420G:User's Manual for PB-420G 2011.03.02. 15:00 Page 6