Getting started – AVer W30 quick guide User Manual
Page 2
Quick Guide
Getting Started
1
1
.
.
M
M
a
a
k
k
e
e
t
t
h
h
e
e
c
c
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
-
Connect the W30 base to a projector, monitor or TV and power.
-
For optimal signal reception, orient both W30 base antennas to 45° angle.
2
2
.
.
C
C
h
h
e
e
c
c
k
k
t
t
h
h
e
e
W
W
3
3
0
0
c
c
a
a
m
m
e
e
r
r
a
a
b
b
a
a
t
t
t
t
e
e
r
r
y
y
l
l
i
i
f
f
e
e
When using the W30 camera for the first time, charge the W30 camera for at least 3
hrs. Green light means the battery is fully charged and Red light means the unit
requires charging. Upon full charge, the W30 camera can stay on for 8 hrs. Whenever
the W30 camera is not being used, please charge the W30 camera.
3
3
.
.
T
T
u
u
r
r
n
n
o
o
n
n
t
t
h
h
e
e
p
p
o
o
w
w
e
e
r
r
Press the power button on the W30 camera first and then base. Upon turning the
power, the unit will start up for about 15-20 sec. You will be able to see the image
from the W30 camera. If
you see “No Signal” on the screen, press RECONNECT
button or bind the unit.
To bind, press MENU > select Binding tab > Connect, and press
to start binding.
Then use a pin or tip of the ball point pen and poke the bind button on the right panel
of W30 camera.
4
4
.
.
O
O
p
p
t
t
i
i
m
m
i
i
z
z
e
e
t
t
h
h
e
e
w
w
i
i
r
r
e
e
l
l
e
e
s
s
s
s
c
c
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
b
b
e
e
t
t
w
w
e
e
e
e
n
n
t
t
h
h
e
e
W
W
3
3
0
0
b
b
a
a
s
s
e
e
a
a
n
n
d
d
c
c
a
a
m
m
e
e
r
r
a
a
Try to position the W30 base away from any interference listed below and also away
the floor and any metal devices. As we know wireless devices are susceptible to
interference from other consumer electronic devices in the 2.4GHz band, in particular:
- Microwave ovens often radiate at 2.4 GHz, especially if they are in bad repair;
- Bluetooth devices use the 2.4 GHz spectrum, shared with Wi-Fi;
- Fusion lighting, sometimes used in high-ceilinged areas, can affect Wi-Fi; and
- Some cordless phones using DECT technology operate at 2.4 GHz.
5
5
.
.
W
W
3
3
0
0
L
L
E
E
D
D
L
L
i
i
g
g
h
h
t
t
Symbol
LED Pattern
State
(1)
Steady Green
Binding the W30 camera with the W30 base.
Continuous Green
Flashing
Data transition. It sends the W30 camera data to W30
base.
(2)
Steady Blue
W30 camera is power on.
No Light
W30 camera is power off.
(3)
Green
Good charge.
Orange
Medium charge.
Red
Low charge. The camera battery has to be charged soon.
Blinking Red
Very low charge. The camera battery has to be charged
immediately.
(4)
Green
Battery is fully charged. You may unplug the power adapter
or continue to use the power source from the power
adapter.
Red
Charging the battery.
No Light
The power adapter is not connected.
© 2013 AVer Information Inc. All rights reserved. For more information, please refer to the user
manual in the software CD.
15 m (45 ft)
45°
45°