Storage, Technical specifications, Definitions for illuminated led indicators – CyberPower Systems Utility Tower Series UPS UP500E User Manual
Page 2
BATTERY REPLACEMENT PROCEDURE:
For UP500E/UP750E only
STORAGE
First turn off your UPS and disconnect its power cord from the wall outlet. Disconnect all cables
connected the UPS to avoid battery drain. To store your UPS for an extended period, cover it and
store with the battery fully charged. Recharge the battery every three months to insure battery life. If
the battery remains uncharged for an extended period of time, it may suffer permanent loss of
capacity.
TROUBLE SHOOTING
Problem
Possible Cause
Solution
Batteries are not fully charged.
Recharge the battery by leaving the UPS
plugged in.
The UPS does not
perform expected
runtime.
Battery is slightly worn out.
Contact CyberPower Systems at
The on/off switch is designed to
prevent damage by rapidly
turning it off and on.
Turn the UPS off. Wait 10 seconds and then
turn the UPS on.
The unit is not connected to an
AC outlet.
The unit must be connected to a 220-240V
50/60Hz outlet.
The battery is worn out.
Contact CyberPower Systems at
The UPS will not
turn on.
Mechanical problem.
Contact CyberPower Systems at
Fuse is blown due to overload
Turn the UPS off and unplug at least one piece
connected equipment. Unplug the power cord of
the UPS then remove the fuse compartment
beneath the power inlet of the UPS and replace
the blown fuse with a spare one. Lock the
compartment back to the UPS. Connect power
cord then turn the UPS on. Make sure that your
spare fuse meets the specification: 6.3A, 250V,
5x10mm.
Batteries are discharged
Allow the unit to recharge for at least 4 hours.
Outlets do not
provide power to
equipment
Unit has been damaged by a
surge or spike.
Contact CyberPower Systems at
The serial cable is not
connected.
Connect the serial cable to the UPS unit and
an open serial port on the back of the
computer. You must use the cable that came
with the unit.
The serial cable is connected to
the wrong port.
Try another serial port of your computer.
The unit is not providing battery
power.
Shutdown your computer and turn the UPS off.
Wait 10 seconds and turn the UPS back on.
This should reset the unit.
PowerPanel
®
is
inactive (all icons
are gray).
The serial cable is not the cable
that was provided with the unit.
You must use the cable included with the unit
for the software.
TECHNICAL SPECIFICATIONS
Model
UP350TE
UP500TE
UP500E UP750E
Capacity (VA)
350VA
500VA
500VA
750VA
Capacity (Watts)
210W
300W
325W
450W
Input
Input Voltage Range
220-240Vac
Frequency Range
50/60 Hz
Output
On Battery Output
Voltage
Simulated Sine Wave at 230Vac +/- 7%
On Battery Output
Frequency
50/60 Hz
Overload Protection
On Utility: Fuse, On Battery: Internal Current Limiting
Surge Protection and Filtering
Lightning / Surge
Protection
Yes
Network Protection
RJ45 (One In/One Out)
Physical
Total # of UPS
Receptacles
2 2
Maximum Dimensions
23.8cm*8.0cm*13.7cm 28.3cm*9.1cm*16.4cm
Weight (Kg)
4.4
5.0
6.4
7.5
Battery
Sealed Maintenance
Free Lead Acid
Battery
12V / 4AHx1
12V / 4.5AHx1
12V / 7AH x1
12V / 9AH x1
User Replaceable
N/A
Yes, Hot Swappable Battery Pack
Typical Recharge
Time
8 Hours
Warning Diagnostics
Indicators
Power On, Using Battery, Boost, Buck
Audible Alarms
On Battery, Low Battery, Overload
Environmental
Operating
Temperature
+32
°F to 95°F ( 0°C to 35°C )
Operating Relative
Humidity
0 to 95% NON-CONDENSING
Communication
PowerPanel
®
Software
Windows 98/ME/2000/NT/XP, Server 2003
Management
Auto-Charger Yes
Auto-Restart Yes
1. Remove the 2 retaining screws then push
the battery cover backward and remove the
cover.
2. Lean the UPS to one side and pull out the
battery partially from the compartment.
Disconnect the battery wires from the
battery, and then remove the battery from
the compartment.
3. Install the replacement battery by connecting
the red wire to the positive (+) terminal of the
battery and connecting the black wire to the
negative (-) terminal of the battery.
4. Slide the battery back into the
compartment. Turn the UPS upside
down to help the batteries entirely slide
into the compartment. Replace the cover
and the retaining screws.
REMINDER: Recharge the unit for 4 – 8
hours to ensure the UPS performs
expected runtime
DEFINITIONS FOR ILLUMINATED LED INDICATORS
Power On
Using
Battery
Fuse
Alarm
Condition
On
Off Normal Off
Normal
Off On
Normal
Two
Beeps
Utility Failure- The UPS is providing battery
power to the Battery-Power Supplied outlets.
Off On
Normal
Rapid
Beeps
Utility Failure- The UPS is providing battery
power. The rapid beeps indicate the battery will
run out of charge within a few minutes.
Off On/Off
Blown
Two beeps
or rapid
beeps
Overload- Occurs in the Full-time Surge
Protection Outlets. Please turn the UPS off and
unplug at least one piece of equipment from the
UPS. Replace the fuse with a spare one then
turn the UPS on.
Off On/Off
Normal/
Blown
Long Beep
Overload- Occurs in the Battery-power Supplied
Outlets. Turn the UPS off and unplug at least
one piece of equipment from the UPS. Check
the fuse and do the replacement if necessary.
Turn the UPS on.
For more information, visi
act
CyberPower Systems B.V.
Flight Forum 3545, 5657DW Eindhoven, The Netherlands
TEL: +31 (0)40 2348170, FAX: +31 (0)40 2340314, E-MAIL:
CyberPower Systems Inc. (USA)
4241 12th Avenue East Suite 400 Shakopee, MN 55379, U.S.A.
Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL:
Entire contents copyright ©2004 CyberPower Systems B.V., All rights reserved. Reproduction in
whole or in part without permission is prohibited. PowerPanel
®
and PowerPanel
®
Plus are
trademarks of CyberPower Systems (USA) Inc.
CyberPower warrants to you, the original purchaser, that CyberPower UPS will be free from defects
in design, assembly, materials and workmanship for two years ( battery is only one year) from the
date of original purchase. Any warranty services, please contact your local dealers or distributors.