Craftsman 316.794991 - Manual (Page 13)

MAINTENANCE AND REPAIR INSTRUCTIONS OPERATING INSTRUCTIONS
BLOWER OPERATIONS
1. Use the blower for trees, shrubs, flower beds, and
hard-to-clean areas.
2. Use the unit around buildings and for other normal
cleaning procedures.
3. Use the blower around walls, overhangs, fences,
and screens.
4. We recommend that a face mask be worn when
operating blower in dusty areas.
5. Stand away from the debris, at a distance that will
easily allow you to control the direction of blown
debris. Never blow debris in direction of bystanders.
6. To control velocity of airstream, blower can be
operated at any speed between idle and full throttle.
Experience with the unit will help you determine the
amount of airflow necessary for each application.
7. Operate power equipment only at reasonable
hours--not early in the morning or late at night when
people might be disturbed. Comply with times listed
in local ordinances.
8. To reduce sound levels, limit the number of pieces of
equipment used at any one time.
9. Operate power blowers at the lowest possible
throttle speed to do the job.
10. Check your equipment before operation, especially
the muffler, air intakes and air filters.
11. Use rakes and brooms to loosen debris before
blowing.In dusty conditions, slightly dampen
surfaces when water is available.
12. Conserve water by using power blowers instead of
hoses for many lawn and garden applications,
including areas such as gutters, screens, patios,
grills, porches and gardens.
13. Watch out for children, pets, open windows or
freshly washed cars, and blow debris safely away.
14. Use intermediate tube plus nozzle of your choice so
the airstream can work close to the ground.
15. After using blowers and other equipment, CLEAN
UP! Dispose of debris in trash receptacles.
OPERATION INSTRUCTIONS
1. Follow the instructions “STARTING A COLD
ENGINE”.
2. Once unit is running, place unit on your back by
slipping arms through the shoulder straps as if your
were putting on a jacket (Figure 17).
3. When preparing to clear an area of debris, always
position yourself so that you can control the direc-
tion debris will be blown .
4. The control handle (A, Fig. 16) and the flexibility of
the blower tube assembly will allow you to clear the
most hard-to-reach areas .
5. The hand grip, throttle trigger, throttle lock and igni-
tion on/off switch (B) are all mounted on a swivel
handle that offers a wide range of operating posi-
tions and comfort (Figure 19).
DO NOT operate the
blower with other
people or animals in the immediate vicinity.
Allow a minimum of 50 feet (15 meters)
between operator and other people or ani-
mals.
CAUTION:
Because of flying
debris, always wear
American National Standards Institute
approved shielded safety glasses or face
shield when operating blower.
WARNING:
Before using your
blower, review Safety
Precautions in your User Manual, and all reg-
ulations for operation of the unit. These pre-
cautions and regulations are for your protec-
tion.
WARNING:
Fig. 17
Fig. 18
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the fre-
quency stated in the table. These procedures should also
be a part of any seasonal tune-up.
NOTE: Maintenance, replacement, or repair of the
emission control devices and system may only be
performed by a Sears or other qualified service
dealer.
NOTE: Maintenance, replacement, or repair of the emis-
sion control devices and system may be perormed
by a Sears or other qualified service dealer.
To prevent serious
injury, never perform
maintenance or repairs with unit running.
Always service and repair a cool unit.
Disconnect the spark plug wire to ensure that
the unit cannot start.
WARNING:
A good preventive maintenance program of regular inspection and care will increase life and improve performance of your
chain saw. This maintenance checklist is a guide for such a program.
Cleaning, adjustment, and part replacement may be required, under certain conditions, at more frequent intervals than
those indicated.
CUSTOMER RESPONSIBILITY
CHECK FOR LOOSE SCREWS/
NUTS/BOLTS
CLEAN OR REPLACE THE FILTER
REPLACE FUEL FILTER
REPLACE SPARK PLUG
INSPECT SPARK ARRESTER SCREEN
INSPECT FUEL HOSES
INSPECT VACUUM TUBES
ITEM BEFORE EACH USE 10 20
MAINTENANCE CHECKLIST
AFTER
EACH USE
HOURS OF
OPERATION
12 13
Fig. 19