Scarlett SC-1146 User Manual

Page 5

www.scarlett-europe.com

SC-1146

INSTRUCTION MANUAL

IMPORTANT SAFEGUARDS
· Before the first connecting of the appliance check that voltage indicated on the rating label corresponds to the mains

voltage in your home.

· For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described

in this instruction manual.

· Do not use outdoors.

· Always unplug the appliance from the power supply before cleaning and when not in use.

· To prevent risk of electric shock and fire, do not immerse the appliance in water or in any other liquids.

· Close supervision is necessary when it is used near children or invalids.

· Do not leave the appliance switched on when not in use.

· Do not use other attachments than those supplied.

· Do not operate after malfunction or cord damage.

· Do not attempt to repair, adjust or replace parts in the appliance. Check and repair the malfunctioning appliance in the

nearest service center only.

· Keep the cord away from sharp edges and hot surfaces.

· Do not pull, twist, or wrap the power cord around appliance.

· Never attempt to take food or liquid out from the container when the blade is moving. Always wait until the motor stops

completely.

· Do not overload the appliance with a food.

· The appliance operates fast and effective. Do not operate continuously for more than 3 min.

FOOD PROCESSOR ASSEMBLING
· Before the first using, wash all removable parts in warm soapy water, rinse thoroughly and dry. Wipe the housing with a

damp cloth.

· Never immerse motor body in any liquid or wash under running water.
· Place the motor unit on a level surface.

ATTENTION: Never operate processor bowl and blender at the same time.
· Place the bowl and turn it clockwise to the proper position.

· Place blender gear safety lid on the seat, rotating until fixed securely.

ATTACHMENTS

· Use ONLY ONE attachment for food processing.
CUTTING KNIFE\PLASTIC BLADE

· Fit shaft adaptor into the blade (or whip maker) until it fixed securely.

· Fit shaft adaptor on the bowl drive spindle.

· Load products to be processed in the bowl.

· Place lid on the bowl and rotate it to lock.

· Start processing at high speed (position II ).
DISKS - GRATING / SLICING / FRENCH-FRIES

· Set the slicer, grater or french-fries knife in the supporting disc and place it onto shaft adaptor.

· Fit the disk with the spindle onto the blender shaft.

NOTE: you must complete assembling fully; otherwise you cannot switch on device.
FOOD PROCESSOR USING
· Please make sure accessories are at its places before switching on.

· Plug-in device.

PULSE MODE

· Turn the Speeds control switch to PULSE position.

· Before processing cut a food so it would pass through a feeder easily.

· Turn control switch to speed "1" (low speed) or "2" (high speed), so food processor will work continuously until you turn

back to "0" (switch off a speed).

· Gradually feed products to be processed through the feed tube only while processor is operating.
CAUTION: Use the pusher only to feed products, push it evenly and gently. The heavier pressure, the coarser chopping.
CAUTION: Do not operate continuously longer than 3 minutes with less than 1 minute intermission.
· Do not overload the appliance by putting in too much food.

· Do not remove any parts during the operating.

BLENDER

· Leave the processor bowl at the place locked into the slot. Remove shaft adaptor and attachments; do not place food

in the processor bowl.

· or:

· Fit processor lid onto bowl drive shaft and fix it.

· Open blender gear safety cap.

· Place the blender jug onto the blender gear. Make sure it properly fitted.

· Put ingredients into blender jar, and close it with the lid.

· Plug-in, turn the switch/press buttons to recommended speed:

"1"(low speed) for liquid ingredients mainly.
"2" (high speed) for heavier processing, i.e. liquid and solid ingredients mixtures.