Great Plains 4000TM Parts Manual - Manual (Page 61)

Revision Comments Part Description Part No. Ref.
Image No. dwg42393
OIL SEAL CR29968 816-595C 1.
BEARING CONE 387-AS 822-238C 2.
BRG CUP 3.81D 382A 822-107C 3.
HUB STUD 5/8-18X2 1/2 GR5 802-182C 4.
NUT LUG 5/8-18 X 90 DEG PLT 803-219C 5.
GREASE ZERK STRAIGHT 1/8-27NPT 800-130C 6.
BRG CUP 2.89ODX.58WD #LM501310 822-053C 7.
BRG CONE 1.62IDX.78WD#LM501349 822-048C 8.
1 HARDENED SPINDLE WASHER 148-404D 9.
NUT HEX SLOTTED 1-14 803-095C 10.
PIN COTTER 7/32 X 2 805-060C 11.
GREASE CAP 3.125 X .38 890-277C 12.
Includes items 1-12 HUB ASSEMBLY; 8-BOLT, 8000LBS 815-301C 13.
SPINDLE 2.75 X 16.29 815-313C 14.
Includes items 1-14 8 BOLT HUB SPINDLE ASM 75-8 815-314C 15.
SPINDLE PIVOT TURBO-CHISEL 566-148D 16.
HHCS 1/2-13X6 GR8 802-820C 17.
NUT HEX TOP LOCK 1/2-13 PLT 803-342C 18.
Rev. 2 S/N C19110H+ TORQUE TUBE WALKING BEAM LH 586-426H 19.
Rev. 2 S/N C19110H+ TORQUE TUBE WALKING BEAM RH 586-427H 19.
Rev. 1 Replaced by 586-426H & 586-427H
(S/N C19109H-)
TORQUE TUBE WALKING BEAM 586-294H 19.
RUBBER 5.18ODX3.04IDX5.12 816-642C 20.
WALKING AXLE BRACKET 586-173H 21.
HHCS 3/4-10X2 1/2 GR8 802-841C 22.
WASHER LOCK SPRING 3/4 PLT 804-023C 23.
NUT HEX 3/4-10 PLT 803-027C 24.
WEAR RING 586-390D 25.
PLASTIC COLLAR 586-391D 26.
PIVOT SPINDLE WASHER 566-149D 27.
WASHER MACH 2.25 X 1.50 X 10GA 804-063C 28.
NUT HEX SLOTTED 1 1/2-12 PLT 803-239C 29.
PIN COTTER 1/4 X 3 PLT 805-115C 30.
HHCS 3/4-10X5 GR5 802-069C 31.
NUT HEX TOP LOCK 3/4-10 803-367C 32.
16.5X12 8 BLT 8 BC 6 PILOT WHT 814-291C 33.
TIRE GOOD YEAR 380/55R16.5 LD F 814-387C 34.
380/55R16.5 OFF WT 814-388C 35.
01/16/13 - 61 - 586-288P
Table of Contents Part Number Index
Section 3: Transport
Center Transport Assembly (S/N C1021H+) 3000
(Applies to 3000TM only)