Great Plains CTA4000 Parts Manual - Manual (Page 27)

Revision Comments Part Description Part No. Ref.
Image No. dwg17147
NUT HEX 1-8 PLT 803-031C 1.
WASHER LOCK SPRING 1 PLT 804-027C 2.
6 1/8 EYE BOLT 194-129H 3.
CTA40 LHW SUBFRM 160-241H 4.
CTA40 RHW SUBFRM 160-242H 4.
HHCS 3/4-10X4 1/2 GR5 802-192C 5.
NUT LOCK 3/4-10 PLT 803-026C 6.
S/N 1077- TRUNNION CASTING MACHINED 194-100D 7.
S/N 1077- PIN ROLL 5/16 X 1 LG 805-156C 8.
S/N 1077- SUBFRAME PIVOT ARM OUTSIDE 194-124H 9.
PIN COTTER 3/16 X 1 1/2 PLT 805-104C 10.
S/N 1077- PIVOT ARM WASHER 194-101D 11.
S/N 1077- HHCS 1 1/8-7X2 1/2 GR5 802-441C 12.
PIN CLEVIS 1 X 3 7/8 USBLE PLT 805-236C 13.
Refer to "Midway Hydraulic Cylinder
(810-368C)"
CYL 2X8X1.12 ROD (TIE ROD) 810-368C 14.
3S BEARING ASSEMBLY 194-123K 15.
HHCS 3/4-10X3 3/4 GR5 802-204C 16.
GREASE ZERK 1/4-28 X 45-DEG 800-058C 17.
WASHER FLAT 3/4 SAE PLT 804-025C 18.
WASHER LOCK SPRING 3/4 PLT 804-023C 19.
NUT HEX 3/4-10 PLT 803-027C 20.
S/N 1077- SUBFRAME PIVOT ARM INSIDE 194-128H 21.
SFCHMS 1/4-20 X 1 1/2 PLT 801-093C 22.
NUT HEX 1/2-13 PLT 803-020C 23.
WASHER LOCK SPRING 1/2 PLT 804-015C 24.
3 BOLT PIVOT CAST W/ BOLT H0LE 120-247D 25.
HHCS 1/2-13X1 3/4 GR5 802-082C 26.
HHCS 3/4-10X7 GR5 802-095C 27.
SUBFRAME ARM RETAINER 195-188H 28.
NUT-LOCK 1/4-20 PLT 803-007C 29.
CTA SF ARM SUPPORT WEAR SPACR 160-568D 30.
CTA SF ARM SUPPORT WEAR PLATE 817-332C 31.
SFCHMS 1/4-20 X 1 1/4 PLT 801-152C 32.
WASHER FENDER 1/4 X 1 804-131C 33.
S/N 1078+ SUBFRAME FLEX ARM, INNER 194-156H 34.
S/N 1078+ SUBFRAME FLEX ARM, OUTER 194-155H 35.
S/N 1078+ SUBFRAME FLEX ARM SPACER, SHORT 194-516D 36.
S/N 1078+ SUBFRAME FLEX ARM SPACER, LONG 194-515D 37.
10/02/13 - 27 - 160-269P
Table of Contents Part Number Index
Frames
Wing Subframes
(Applies to CTA4000 only)