Great Plains 3N-4025P Parts Manual - Manual (Page 41)

Revision Comments Part Description Part No. Ref.
Image No. dwg22510
VERIS PPC-40 CONTROLLER 833-251C 1.
COLLAR LOCK 7/8 HEX 402-058D 2.
SCREW SET 5/16-18 SKT KP X 3/8 801-035C 3.
LOCK COLLAR, 7/8 HEX W/ SET SC 402-025S 4.
2nd rev. SPKT 50C36 X 7/8 HEX BORE 808-313C 5.
S/N 1045PP+ SPKT 50C17 X 7/8 HEX BORE 808-303C 6.
CHAIN RL #50 92 PITCHES 136-200D 7.
RHSNB 5/16-18X1 GR5 802-282C 8.
FLANGETTE 52 3-BOLT PLT 822-175C 9.
BRG INS 7/8HEXX2.04OD SPH 822-195C 10.
803-184 FLG TP LK 5/16-18ZNYCR 803-177C 11.
WASHER FLAT 1/2 USS HARD PLT 804-113C 12.
WASHER LOCK SPRING 1/2 PLT 804-015C 13.
NUT HEX 1/2-13 PLT 803-020C 14.
IDLER SPOOL #50 2.38X1.01X.31 817-456C 15.
TUBE RND 1 OD X 7/32W X 2.13 120-306D 16.
HHCS 1/2-13X4 1/2 GR5 SPTHD 802-672C 17.
SHAFT 7/8 HEX X 16.5 120-001D 18.
U-JOINT DRIVE SHAFT YOKE 196-245H 19.
SPKT 50A25 CLUTCH METRIC BORE 808-357C 20.
CHAIN RL #50 92 PITCHES 136-200D 21.
OGURA CLUTCH 823-231C 22.
40P CENTER CLUTCH SHAFT 196-776D 23.
PIN ROLL 1/4 X 1 1/2 LG PLT 805-180C 24.
2nd rev. S/N 1045PP+ SPKT 50C34 X 7/8 HEX BORE 402-167H 25.
1st rev. S/N 1044PP- SPKT 50C27 X 7/8 HEX BORE 808-311C 25.
2nd rev. S/N 1045PP+ CHAIN RL #50 80 PITCHES 136-220D 26.
1st rev. S/N 1044PP- CHAIN RL #50 72 PITCHES 136-202D 26.
HSHCS M8X1.25X30 GR8.8 PLT 802-775C 27.
WASHER MACH 1.50 X 1.00 X 18GA 804-061C 28.
2nd rev. S/N 1045PP+ SPKT 50B21 X 1 BORE W/KW, 2 SS 808-294C 29.
1st rev. S/N 1044PP- SPKT 50B17 X 1 BORE W/KW, 2 SS 808-344C 29.
HHCS 1/4-20X5 GR5 PLT 802-085C 30.
NUT-HEX 1/4-20 PLT 803-006C 31.
TUBE RND DOM. 1 OD X 7/32WX3.0 120-293D 32.
SPKT 50C22 X 7/8 HEX BORE 808-306C 33.
HEX SHAFT 7/8 X 162.0 LG PLT 196-772D 34.
VERIS DRIVE SUPPORT SPACER 196-847D 35.
HHCS 5/8-11X2 1/2 GR5 802-058C 36.
WASHER LOCK SPRING 5/8 PLT 804-022C 37.
NUT HEX 5/8-11 PLT 803-021C 38.
CLUTCH SPROCKET SPACER 196-876D 39.
WASHER FLAT 1/4 USS PLT 804-075C 40.
WASHER LOCK SPRING 1/4 PLT 804-006C 41.
KEY 1/4 X 3/16 X 3.80 839-956C 42.
BUSHING 1 1/8 ODX7/8 HEX BORE 196-877D 43.
SPLIT SPACER 1 ID X 1.25 THICK 120-337S 44.
TUBE RND 1 OD X 7/32W X 2.13 120-306D 45.
CLUTCH OIL SHIELD 402-507D 46.
BUTTON PLUG 7/8 ROUND HOLE 817-813C 47.
04/10/13 - 41 - 196-286P
Table of Contents Part Number Index
Drive
HD10 & 25 Series Center Section Drive
(Applies to 3N-4025P only)