Great Plains 3N-3020P Parts Manual - Manual (Page 41)

Revision Comments Part Description Part No. Ref.
Image No. dwg20033
SPKT 50C17 X 7/8 HEX BORE 808-303C 1.
SPKT 50C23 X 7/8 HEX BORE 808-307C 1.
FLANGETTE 52 3-BOLT PLT 822-175C 2.
BRG INS 7/8HEXX2.04OD SPH 822-195C 3.
803-184 FLG TP LK 5/16-18ZNYCR 803-177C 4.
RHSNB 5/16-18X1 GR5 802-282C 5.
STUB SHAFT 7/8 HEX 13.94 LG 196-580D 6.
PIN ROLL 1/4 X 1 1/2 LG PLT 805-180C 7.
WASHER MACH 1.50 X 1.00 X 18GA 804-061C 8.
SPKT 50C44 X 7/8 HEX BORE 808-314C 9.
HHCS 1/2-13X4 FTHD 802-424C 10.
WASHER FLAT 1/2 USS HARD PLT 804-113C 11.
IDLER SPOOL #50 2.38X1.01X.31 817-456C 12.
TUBE RND 1 OD X 7/32W X 2.13 120-306D 13.
NUT HEX 1/2-13 PLT 803-020C 14.
TRANS REAR SHFT 7/8 HEX 18.41L 196-584D 15.
7 1/2", 10" & 15" Spacing LINE SHAFT 7/8 HEX 85.50 LG 196-579D 16.
Twin Row Spacing SHAFT 7/8 HEX, 76.0 LONG PLTD 120-307D 16.
RHSNB 3/8-16X1 3/4 GR5 802-252C 17.
IDLER BOLT PLATE 402-242D 18.
DOUBLE IDLER SPOOL ASSY #50 196-249S 19.
NUT FLANGE LOCK 3/8-16 PLT 803-209C 20.
U-JOINT DRIVE SHAFT YOKE 196-245H 21.
CHAIN RL #50 77 PITCHES 136-149D 22.
CHAIN RL #50 88 PITCHES 136-178D 23.
TRANS FRT SHAFT 7/8 HEX 12.16L 196-583D 24.
SPKT 50C30 X 7/8 HEX BORE 808-319C 25.
OFFSET DOUBLE IDLER WELDMENT 402-126H 26.
TUBE RND 1 OD X 7/32W X 1.56 120-305D 27.
WASHER FLAT 1/2 USS PLT 804-017C 28.
PIN COTTER 7/64 X 1 LONG 805-064C 29.
CHAIN RL #50 X 81 PITCHES 136-179D 30.
TUBE RND DOM. 1 OD X 7/32WX3.0 120-293D 31.
SPKT 50C22 X 7/8 HEX BORE 808-306C 32.
COLLAR LOCK 7/8 HEX 402-058D 33.
SCREW SET 5/16-18 SKT KP X 3/8 801-035C 34.
LOCK COLLAR, 7/8 HEX W/ SET SC 402-025S 35.
1st Rev. S/N 1068AA- SPRKT STORAGE WELD 402-022H 36.
HHCS 3/8-16X1 1/4 GR5 802-079C 37.
PIN LINCH 3/16 X 1 9/16 LONG 805-240C 38.
WASHER LOCK SPRING 1/2 PLT 804-015C 39.
SPKT 50C28 X 7/8 HEX BORE 808-312C 40.
04/10/13 - 41 - 196-248P
Table of Contents Part Number Index
Drive
Transmission Drive
(Applies to 3N-3010P, 3N-3020P only)