Table of contents part number index – Great Plains 3SF45 Parts Manual User Manual
Page 35
Revision
Comments
Part Description
Part No.
Ref.
Image No.
dwg16690
Used 1/1986-8/1990.
AXLE SHAFT WELDMENT - DUAL
172-070E
1.
Used 1/1986-8/1990.
DUAL GAUGE WHEEL SPACER
172-068D
2.
Used 1/1986-8/1990.
6 BOLT HUB - MACHINED
172-071D
3.
Used 1/1986-8/1990.
ROTATING COLLAR
172-067D
4.
Used 1/1986-8/1990.
PIN SPIROL 1/2X2 1/2 PLAIN
805-037C
5.
Used 8/1990-11/1992.
PIN ROLL 5/16 X 2 1/2 PLT
805-125C
6.
Used 8/1990-11/1992.
GW DRIVE SPROCKET - CENTER
172-095D
7.
Used 8/1990-11/1992.
DUAL GW SHAFT WELD - CENTER
172-087E
8.
SNAP RING INT3.523OD N5000-315
800-053C
9.
Used 8/1990-11/1992.
BRG BALL 1.96IDX3.14ODX.62
822-087C
10.
Used 8/1990-11/1992.
GW SHAFT SEAL - CENTER
816-085C
11.
Used 8/1990-11/1992.
HUB SPACER - 1 3/4 ID
172-096D
12.
Used 8/1990-11/1992.
MF WING GW HUB MACHINED 6 BOLT
200-017D
13.
Used 8/1990-11/1992.
HUB RETAINER SLEEVE
181-061D
14.
ACREMETER 45' 3 SECTION
890-093C
15.
36' ACREMETER
890-101C
15.
BEARING GAUGE WHEEL
822-028C
16.
Used 1/1986-8/1990.
AXLE SHAFT WELDMENT - SINGLE
172-069E
17.
GW ARM - DRIVE LH BOX
172-055E
18.
GW ARM - DRIVE RH & CTR
172-058E
18.
TUBE CAP
172-065D
19.
WASHER FLAT 1/4 SAE PLT
804-007C
20.
WASHER LOCK SPRING 1/4 PLT
804-006C
21.
NUT-HEX 1/4-20 PLT
803-006C
22.
3/8 SQUARE SPROCKET KEY
172-083D
23.
Used 1/1986-8/1990.
RPBY 808-051C
172-338D
24.
2nd rev.
CHAIN RL #40 94 PITCHES
136-010D
25.
Use existing stock; 1st rev.
RPBY 136-010D
809-043C
25.
#40 CONNECTOR LINK-PLATED
809-096C
26.
Used until 11/1992.
HHCS 5/16-18X3/4 GR5
802-007C
27.
Used until 11/1992.
WASHER LOCK SPRING 5/16 PLT
804-009C
28.
Used until 11/1992.
NUT HEX 3/8-16 PLT
803-014C
29.
Used until 11/1992.
WASHER LOCK SPRING 3/8 PLT
804-013C
30.
Used until 11/1992.
WASHER FLAT 3/8 USS PLT
804-011C
31.
Used until 11/1992.
CHAIN IDLER PLATE
172-066D
32.
Used until 11/1992.
GW AXLE COLLAR TAB
109-084D
33.
Used until 11/1992.
IDLER BLOCK
890-084C
34.
Used until 11/1992.
RHSNB 3/8-16X3 GR5
802-195C
35.
Used 8/1990-11/1992.
SINGLE GW SHAFT WELD - CENTER
172-086E
36.
Used 8/1990-11/1992.
PIN SPIROL 1/2 X 2 3/4
805-098C
37.
2nd rev.
Used 1/1988-11/1992.
CHAIN RL #40 79 PITCHES
136-014D
38.
Use existing stock; 1st rev.
REPLACED BY 136-014D
809-044C
38.
Used 1/1986-11/1992.
SPKT 40B19X1 BORE W/5/16 H
808-053C
39.
Used 1/1986-11/1992.
PIN ROLL 5/16 X 2 1/4 PLT
805-029C
40.
Used 1/1986-11/1992.
LOWER JACKSHAFT
172-073D
41.
AXLE TUBE BUSHING - MACHINED
172-072D
42.
GREASE ZERK STRAIGHT 1/4-28
800-001C
43.
JACK SHAFT - KEY
109-031D
44.
3rd rev.
SPKT 40B19X1 B MAX .875 THRU
808-125C
45.
Use existing stock; 2nd rev.
REPLACED BY 808-125C
152-312D
45.
Use existing stock; 1st rev.
RPBY 152-312D
808-052C
45.
NUT HEX 5/8-11 PLT
803-021C
46.
WASHER LOCK SPRING 5/8 PLT
804-022C
47.
HHCS 5/8-11X2 GR5
802-055C
48.
BOLT WHEEL 1/2-20X1 90-DEG
802-104C
49.
VALVE STEM TR415X.625X1 1/4 LG
816-035C
50.
RPBY 814-011C
814-026C
51.
12/26/12
- 35 -
170-062P
Gauge Wheels
Drive Gauge Wheel Assembly (1/1986-11/1992)
(Applies to 3SF36 (1986+), 3SF45 (1986+) only)