Great Plains TSF1260 Parts Manual - Manual (Page 53)

Revision Comments Part Description Part No. Ref.
Image No. dwg23289
(S/N A1054F+) (S/N A1003G+) CENTER SECT WELD 60FF NARROW 506-289H 1.
(S/N A1053F-) (S/N A1002G-) CENTER SECTION WELDMENT 60FF 506-269H 1.
NUT LOCK 5/8-11 PLT 803-024C 2.
SHIM - INNER PIVOT ATTACH 506-826D 3.
INNER PIVOT PIN WELD UPPER 506-223H 4.
HHCS 5/8-11X2 1/4 GR5 802-057C 5.
WASHER - THRUST 506-493D 6.
BUSHING 2 1/2 X 2 X 3 CONNEX 890-802C 7.
Refer to page 5-1 for breakdown (S/N
A1068F-)
CYL 2.5X10X1.06 ROD (TIE) LH 810-022C 8.
Refer to page 5-1 for breakdown (S/N
A1068F-)
CYL 2.5X10X1.06 ROD (TIE) RH 810-018C 8.
Refer to Wing Lift Cylinder (810-591C)
For breakdown (S/N A1069F+)
CYL 2.5X11X1.25 ROD (TIE) 810-591C 8.
GREASE ZERK 1/4-28 X 45-DEG 800-058C 9.
INNER PIVOT PIN WELD LOWER 506-222H 10.
INNER PIVOT TUBE WELD SHEAR-LH 506-252H 11.
HHCS 1/4-20X1 GR5 802-005C 12.
NUT HEX FLNG T-LOCK 1/4-20 YLW 803-293C 13.
BUSHING CYL 1 1/4 X 1 X 1 890-005C 14.
GREASE ZERK STRAIGHT 1/4-28 800-001C 15.
PIN CLEVIS 1 X 2 3/4 USABLE LG 805-004C 16.
(2007+) OREL 1/16 9/16MJIC 9/16MORB 811-337C 17.
(2006-) OREL 1/32 9/16MJIC 9/16MORB 811-062C 17.
HHCS 3/4-10X3 GR5 802-383C 18.
NUT HEX JAM 3/4-10 PLT 803-048C 19.
CABLE PULLEY CF500/600 99 817-370C 20.
Refer to page 5-3 for breakdown CYL 3X12X1.25 ROD (TIE ROD) 810-312C 21.
NUT FLANGE LOCK 3/8-16 PLT 803-209C 22.
HHCS 3/8-16X2 3/4 GR5 802-216C 23.
1/8 WIRE ROPE CLIP 890-631C 24.
CABLE SWING LOCK ACTUATOR 90' 890-803C 25.
CLEVIS 890-520C 26.
HYD HOSE CLAMP BRACKET 502-068D 27.
HOSE CLIP 13/16 ID 800-064C 28.
WASHER LOCK SPRING 5/16 PLT 804-009C 29.
HHCS 5/16-18X1 GR5 802-159C 30.
U-BOLT 3/8-16 X 3 1/32 X 4 806-021C 31.
BRACKET - FOLD SWITCH/LIGHT RH 506-867D 32.
NUT HEX FLANGE 3/8-16 PLT 803-068C 33.
BOOM LOCK CABLE HOLD-DOWN 506-869D 34.
HFS 1/2-13 X 3 GR5 802-656C 35.
BUSHING 7/8 X 5/8 X 1 CONNEX 890-852C 36.
(S/N A1054F+) Shown (S/N A1003G+) INNER PIVOT CYL PLATE WELD LH 506-290H 37.
(S/N A1054F+) (S/N A1003G+) INNER PIVOT CYL PLATE WELD RH 506-291H 37.
(S/N A1053F-) (S/N A1002G-) INNER PIVOT SHEAR PLATE ASY 506-263V 37.
NUT HEX FLANGE 1/2-13 GR G PLT 803-193C 38.
TILT PIVOT PIN 506-484D 39.
HHCS 3/8-16X3 GR5 802-024C 40.
NUT LOCK 3/8-16 NYLON INSERT 803-078C 41.
SCR HEX SELF TAP 1/4-20X1TYPEF 801-151C 42.
Shown DUAL AG LIGHTS LH 890-311C 43.
DUAL AG LIGHTS RH 890-312C 43.
HHCS 5/8-11X2 GR5 802-055C 44.
Shown INNER PIVOT SHEAR STOP WELD LH 506-257H 45.
INNER PIVOT SHEAR STOP WELD RH 506-256H 45.
SP EYE 3/8-16X 3 7/8 802-567C 46.
09/07/11 - 53 - 500-642P
Table of Contents Part Number Index
Boom
Boom To Center Frame
(Applies to TSF1060, TSF1260 only)