Great Plains PT8030 Predelivery Manual - Manual (Page 33)

Revision Comments Part Description Part No. Ref.
Image No. dwg15260
6030 S/N U1048-; 8030 S/N V1012- COVER, MOUNT 402-102D 1.
6030 S/N U1048-; 8030 S/N V1012- MOUNT WELD 402-040H 2.
BEARING .880 HEX BORE 205DD 188-006V 3.
WASHER MACH 1.50 X 1.00 X 18GA 804-061C 4.
PLASTIC SLEEVE 817-229C 5.
6030 S/N U1048-; 8030 S/N V1012- DRIVE WHEEL ARM WELD 402-039H 6.
6030 S/N U1049+; 8030 S/N V1013+ CONTACT DRIVE WHEEL ARM WELD 402-125H 6.
6030 S/N U1048-; 8030 S/N V1012- SHIELD RH, WELD 402-042H 7.
6030 S/N U1048-; 8030 S/N V1012- SHIELD LH, WELD 402-043H 7.
Shown. 6030 S/N U1049+; 8030 S/N
V1013+
CONTACT WHL DRIVE SHIELD LH 402-124H 7.
6030 S/N U1049+; 8030 S/N V1013+ CONTACT WHL DRIVE SHIELD RH 402-123H 7.
HFSS 1/2-13X1 GR5 802-568C 8.
STOP, SPRING MOUNT 402-105D 9.
803-206CCOUPLER 3/8-16 X 1 3/4 803-201C 10.
HFSS 3/8-16X1 1/2 GR5 802-569C 11.
2nd rev. HHCS 1/2-13X4 FTHD 802-424C 12.
use existing stock; 1st rev. HHCS 1/2-13X4 1/2 GR5 802-413C 12.
SLEEVE, SPRING MOUNT 402-107D 13.
PIN, SPRING MOUNT 402-106D 14.
NUT HEX JAM 1/2-13 PLT 803-036C 15.
SPRING PLUG CASTING 204-017D 16.
SPRING HOLD DOWN HD COULTER 807-055C 17.
TIRE/WHEEL ASSY 13/5 X 6 814-134C 18.
BRACE WELD, GUAGE WHEEL 402-038H 19.
6030 S/N U1048-; 8030 S/N V1012- HEX BAR, DRIVE WHEEL 402-108D 20.
6030 S/N U1049+; 8030 S/N V1013+ HEX BAR, DRIVE WHEEL 402-252D 20.
PIN COTTER 1/4 X 2 PLT 805-021C 21.
NUT FLANGE LOCK 3/8-16 PLT 803-209C 22.
6030 S/N U1049+; 8030 S/N V1013+ DRIVE MODULE TOP COVER 817-341C 23.
6030 S/N U1049+; 8030 S/N V1013+ CLIP U-TYPE NUT 1/4-20 SLF-RET 800-163C 24.
6030 S/N U1049+; 8030 S/N V1013+ HHCS 1/4-20X5/8 GR5 802-078C 25.
6030 S/N U1049+; 8030 S/N V1013+ MOUNT WELD 402-128H 26.
07/22/10 - 33 - 401-032P
Table of Contents Part Number Index
Drives
Contact Drive Wheel
(Applies to PT6030, PT8030 only)