Great Plains YP3025 Parts Manual - Manual (Page 57)

Revision Comments Part Description Part No. Ref.
Image No. dwg31370
DRIVESHAFT 3PYP PLANTER 826-502C 1.
M6X1X3.5MM THD ZERK 826-501-2 6560007 2.
PIN ROLL 1/4 X 2 LG PL 805-146C 3.
SHAFT 7/8 HEX 18.00 LONG 401-747D 4.
Shown LH WING FRAME WLDMT YP30 401-678H 5.
RH WING FRAME WLDMT YP30 401-679H 5.
DRIVE PLATES BRACE 401-563D 6.
WASHER MACH 1.50 X 1.00 X 18GA 804-061C 7.
FLANGETTE 52 3-BOLT PLT 822-175C 8.
BRG INS 7/8HEXX2.04OD SPH 822-195C 9.
LOCK COLLAR, 7/8 HEX W/ SET SC 402-025S 10.
OGURA CLUTCH 823-231C 11.
CLUTCH SPROCKET SPACER 196-876D 12.
SPKT 50A25 CLUTCH METRIC BORE 808-357C 13.
HSHCS M8X1.25X30 GR8.8 PLT 802-775C 14.
CHAIN RL #50 82 PITCHES 136-236D 15.
HHCS 1/4-20X6 GR5 PLT 802-893C 16.
NUT HEX 1/4-20 PLT 803-006C 17.
WASHER FLAT 1/4 SAE PLT 804-007C 18.
HHCS 1/2-13X3 1/2 GR5 802-041C 19.
WASHER FLAT 1/2 USS HARD PLT 804-113C 20.
TUBE RND DOM. 1 OD X 7/32WX3.0 120-293D 21.
IDLER SPOOL #50 2.38X1.01X1.31 817-456C 22.
WASHER LOCK SPRING 1/4 PLT 804-006C 23.
WASHER LOCK SPRING 1/2 PLT 804-015C 24.
NUT HEX 1/2-13 PLT 803-020C 25.
Used with 44 Row 7 1/2", 12 Row 30",
12 Row 70cm, 18 Row 20", 24 Row
Twin Row & 24 Row 15" Row
Spacing
SHAFT 7/8 HEX, 113 LG PLT 401-989D 26.
Used with 36 Row 10", 23 Row 15" &
23 Row 35cm Row Spacing
SHAFT 7/8 HEX, 106.0 LONG PLTD 120-308D 26.
SPKT 50C30 X 7/8 HEX BORE 808-319C 27.
CLAMP WRM DRV #20SS (.81-1.75) 800-257C 28.
CLUTCH OIL SHIELD 402-507D 29.
BUTTON PLUG 7/8 ROUND HOLE 817-813C 30.
HHCS M8X1.25X14 GR8.8 802-782C 31.
NUT HEX NYLOCK M8X1.25 PLT 803-278C 32.
BUSHING 1 1/8 ODX7/8 HEX BORE 196-877D 33.
KEY 1/4 X 3/16 X 3.80 839-956C 34.
EC YOKE ASSY 1071001 35.
EC CROSS ASSEMBLY (U JOINT) 1001020 36.
EC GREASE ZERK M6X1 EXTRA SHRT 6561306 37.
EC OUTER TUBE YOKE 1701027 38.
EC INNER TUBE YOKE 1701029 39.
CLAMP WRM DRV#28 SS(1.31-2.25) 800-125C 40.
DRIVE SHAFT BELLOWS - LONG 816-587C 41.
06/04/14 - 57 - 401-703P
Table of Contents Part Number Index
Drive
Wing Drive
(Applies to YP30 only)