Great Plains YP1625-3115 31 Row 15 Inch Quick Start - Manual (Page 5)

Quick Setup Guide for IntelliAg Model YP1625 15”
11001-1594-201108
©2011 DICKEY-john Corporation
Specifi cations subject to change without notice.
System Component Installation
Locate and install system components as shown in the
diagram. Note how the modules are identifi ed and which
modules are located on which sections in this system.
Connect WSMB module harnesses together with included
extensions. Modules connect to the WSMT harness connec-
tion. Plug all unused connectors with included dust plugs.
Secure any excess wires with tie-wraps.
See Operator’s Manual for additional installation information.
Power on monitor and program with correct constants as
described on this Quick Start Guide.
1.
2.
3.
4.
5.
5
467980847
Extension
Harness 20’
WSMB
Module
Harness
467981201A
WSMB
Module
Seed Monitor
467981100S1
467980143
Extension
Harness 25’
WSMT
Module
Harness
467980851
Connect to
Actuator
Harness
467980160
467980143
Extension
Harness 25’
WSMB
Module
WSMB
Module
Harness
467981201A
Seed Monitor
467981100S1
Standard Dj SE Style
Planter Harness
Right Section
Standard Dj SE Style
Planter Harness
Can
Terminator
Connect Cab
Harness to
Implement CAN
Harness
Radar Speed Sensor
467833000S1
Mounting Kit
467830760
(Radar connected to either
tractor harness
or WSMT as shown below)
Virtual
Terminal
Chassis
Ground
CAN
Terminator
467980126
Ignition
Connect to switched
+12VDC
NOTE: This wire
must be connected to
switched +12VDC
Master
Switch
+ -
Tractor Cab Harness
467980455
Battery
CFM
Tractor ECU
Controller
(467980451)
or
Task Controller
(467980452)
(10” VT ONLY)
Harness
467980452
(5” Terminal) or
Harness
467980451A
(10” Terminal)
467984261S1
Tractor Harness
RS232
GPS
(467980451 Harness)
467983502
467982000S1
Hydraulic
Tongue
Option Connect to
Harness 467980134
Connect to
467980144
Extension
Note: Connect the WSMT
Actuator harness and the
Dj Planter Harness to the
mating connectors of the
WSMT Module harness
467980710S3
Harness
Planter
Output
Module
464820517
Output 2 Hitch B1
Output 2 Hitch B2
Output 1 Lift
Output 1
Left Clutch
464820517S1
Output 1 Marker
Output 2 Fold
Planter
Output
Module
2 Solenoid Driver
464820511S1
467983504
467982000S1
Clutch
Control
Output 2
Not used
Right
Clutch
Output 1
2 Solenoid Driver
464820518S1
20’ Extension
467980471
Not used
Output 2
Hopper
Level Sensor
466820720S3
Hopper Extension
Harness
466820714
Accessory Sensors
connection to WSMT
ACTUATOR HARNESS
467980160
Application
Rate Sensors
(Channel 1-4 Feedback)
Labeled FB1-FB4
PWM Solenoid Valves
Channel 1-4 Control
Labeled PWM 1-PWM 4
Implement Lift Sensor
464820520S1
If no implement lift
sensor is used, connect
the IMP LIFT leads
together
Fan/Shaft
RPM Sensor
466970014S1
Hall Effect
Sensor
466970016S1
Servo Valves
(Labeled Servo 1
and Servo 2)
Actuator Harness
467980160
Test Switch
Implement Lift
Extension Harness
466820713
WSMT
467980815S1
Left Section
Row 4
Row 5
Row 6
Row 7
Row 8
Row 9
Extension 30’
45790811
Extension 15’
466820830
Implement CAN
Breakaway Harness
467980134
Connect to Optional
Hydraulic Tongue Harness
or to Extension
CFM Harness
467980330
Fan
Extension
Harness 3’
459680920
Hopper Level
Sensor
466820720S3
466820832S1
Extension 5’
Row 10
Row 11
Row 1
Row 2
Row 3
Row 12
Row 13
Row 14
Row 15
Row 16
Row 20
Row 21
Row 22
Row 23
Row 24
Row 25
Row 26
Row 27
Row 17
Row 18
Row 19
Row 28
Row 29
Row 30
Row 31