Great Plains ADI445 Parts Manual - Manual (Page 2)

ADI434 & ADI445 Air Drill Implement 160-192P
Great Plains Mfg., Inc. Section 1 Introduction
© Copyright 1999 All rights Reserved
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the prep-
aration of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the
use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit This publication describes the
state of this product at the time of its publication, and may not reflec the product in the future. The illustrations in this manual are not intended for safe and proper assembly
or disassembly of equipment. The illustrations are intended for ordering parts only.
Great Plains Manufacturing, Incorporated Trademarks
The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
Table of Contents
Table of Contents Index
Section 1 Introduction. . . . . . . . . . . . . . . . . . . . . . 1-1
General Information . . . . . . . . . . . . . . . . . . . . 1-1
Revisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Touch-up Paint and Manual Information . . . . . . 1-1
Replacement Hardware . . . . . . . . . . . . . . . . . . 1-1
Part Number Service Coding . . . . . . . . . . . . . . 1-2
Part Number Index . . . . . . . . . . . . . . . . . . . . . . 1-3
Section 2 Towers . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Tower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Section 3 Frames . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Frame #1 to Frame #2 . . . . . . . . . . . . . . . . . . . 3-1
Frame #2 to Frame #3 . . . . . . . . . . . . . . . . . . . 3-3
Frame #3 to Frame #4 . . . . . . . . . . . . . . . . . . . 3-5
Frame #4 to Frame #5 . . . . . . . . . . . . . . . . . . . 3-7
Frame #5 to Frame #6 . . . . . . . . . . . . . . . . . . . 3-9
Slow Moving Vehicle Emblem . . . . . . . . . . . . 3-11
Cart Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Light Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Section 4 Gauge Wheel . . . . . . . . . . . . . . . . . . . . . 4-1
Dual Gauge Wheel . . . . . . . . . . . . . . . . . . . . . . 4-1
Single Gauge Wheel . . . . . . . . . . . . . . . . . . . . 4-3
Dual Gauge Wheel Lift Assist Wheel . . . . . . . . 4-5
Single Lift Assist Wheel . . . . . . . . . . . . . . . . . . 4-7
Transport Wheel and Tire . . . . . . . . . . . . . . . . . 4-9
Section 5 Opener System . . . . . . . . . . . . . . . . . . . 5-1
Spring Reset Hoe Opener . . . . . . . . . . . . . . . . 5-1
1 11/16" Offset Spring Reset Hoe Opener . . . . 5-3
Shear Bolt Hoe Opener . . . . . . . . . . . . . . . . . . 5-5
C-Shank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Coulter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Coulter Fertilizer Attachment . . . . . . . . . . . . . 5-11
Shear Bolt Hoe Opener . . . . . . . . . . . . . . . . . 5-13
Section 6 Press Wheels . . . . . . . . . . . . . . . . . . . . 6-1
Press Wheel Hangers and Rigid Adjustment . . 6-1
Spring Cushioned Press Wheel Adjustment . . 6-3
12 Wheel Press Wheel Gang (Short Frame) . . 6-5
12 Wheel Press Wheel Gang . . . . . . . . . . . . . . 6-7
13 Wheel Press Wheel Gang . . . . . . . . . . . . . . 6-9
2 x 20 Rubber Press Wheel . . . . . . . . . . . . . . 6-11
Rock Guards and Press Wheel Scrapers . . . 6-13
Section 7 Hydraulics . . . . . . . . . . . . . . . . . . . . . . . 7-1
Folding Hydraulics . . . . . . . . . . . . . . . . . . . . . . 7-1
Transport Hydraulics . . . . . . . . . . . . . . . . . . . . 7-3
Rephasing Cylinder (810-124C) . . . . . . . . . . . 7-5
Rephasing Cylinder (810-218C) . . . . . . . . . . . 7-7
Rephasing Cylinder (810-221C) . . . . . . . . . . . 7-9
Rephasing Cylinder (810-287C) . . . . . . . . . . 7-11
Hydraulic Cylinder 5" x 40" x 1 1/2"
(810-292C) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Hydraulic Cylinder 4" x 20" x 1 1/2"
(810-309C) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Pilot Operated Check Valve (810-086C) . . . . 7-17
Sequence Valve (810-006C) . . . . . . . . . . . . . 7-19
Flow Divider (810-286C) . . . . . . . . . . . . . . . . 7-21
Section 8 Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Decal Placement . . . . . . . . . . . . . . . . . . . . . . . 8-1
4/15/99
Section 1 Introduction
ADI434 & ADI445 Air Drill Implement 160-192P