Clarion DXZ755MC - Manual (Page 21)

280-8171-00
DXZ755MC
21
English
2. Each time you press the [ERASE] button, the
display switches in the following order:
TRACK ERASE ➜ FOLDER ERASE ➜
Normal mode
Notes:
• When a selected track or folder is erased, the ap-
proximate recordable time is shown (the record-
able time shown varies according to the set re-
cording mode).
• Do not turn off the power to the unit or switch the
operation mode during erasing recordings.
●TRACK ERASE
1. Press the [SRC] button to select the
M.CATCHER mode.
2. Play back a track to be erased, and press
the [ERASE] button to select “TRACK
ERASE”.
3. Press and hold the [ ] button for 2 sec-
onds or longer. The display shows “ERAS-
ING” as the track currently being played back
is erased.
●FOLDER ERASE
1. Press the [SRC] button to select the
M.CATCHER mode.
2. Play back any track of the folder to be
erased, and press the [ERASE] button to se-
lect “FOLDER ERASE”.
3. Press and hold the [ ] button for 2 sec-
onds or longer. The display shows “ERAS-
ING” as the folder currently being played
back is erased.
●ALL ERASE
1. Press the [SRC] button to select the
M.CATCHER mode.
2. Press the [ERASE] button for 2 seconds or
longer to select “ALL ERASE”.
3. Press and hold the [ ] button for 2 sec-
onds or longer. The display shows “ERAS-
ING” as ALL ERASE is executed.
Remaining capacity of the memory
By pressing the [REC] button while in the
M.CATCHER mode, the remaining capacity of
the flash memory can be displayed for 4 sec-
onds as an approximate recordable time in “MM
(minute): SS (second)”.
The display shows “AVIL. 123:45”.
Note:
• The recordable time shown varies according to
the set recording mode
MUSIC CATCHER Operations
Display Adjust Mode
Setting the clock
1. Press and hold the [DISP] button for 1 second
or longer to switch to the display adjust mode.
2. Move the [ a]/[d] lever to select “CLOCK”.
3. Press the [ ] button.
4. Move the lever to select the hour or the
minute.
5. Turn the [ROTARY] knob to set the correct
time.
∗ The clock is displayed in 12-hour format.
6. Press the [ ] button to store the time into
memory.
7. Press the [DISP] button to return to the previ-
ous mode.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the car’s
battery or take out this unit, the clock is reset.
While setting the clock, if another button or opera-
tion is selected, the clock set mode is canceled.
Switching the patterns of the
spectrum analyzer display
∗ The factory default setting is “SRC ICON”.
1. Press and hold the [DISP] button for 1 second
or longer to switch to the display adjust mode.
2. Move the [ a]/[d] lever to select “SPE/ANA
PTN”.
3. Turn the [ROTARY] knob to select the set-
ting. Each time you turn the [ROTARY] knob,
the setting changes in the following order:
1 ➜ 2 ➜ 3 ➜ 4 ➜ SRC ICON
∗ “SRC ICON” cannot be selected in the sub
display.
4. Press the [DISP] button to return to the previ-
ous mode.
Setting the sensitivity of the
spectrum analyzer display
∗ The factory default setting is “MID”.
1. Press and hold the [DISP] button for 1 second
or longer to switch to the display adjust mode.
2. Move the [ a]/[d] lever to select “S/A
SENS”.
3. Turn the [ROTARY] knob to select from
“LOW”, “MID” or “HIGH”.
4. Press the [DISP] button to return to the previ-
ous mode.
Common Operations