Craftsman 316.7948 User Manual

Page 10

OPERATING INSTRUCTIONS

ADJUSTING THE SUSPENSION SYSTEM
1.

Place the unit’s shoulder supports over the shoulders while the
unit is behind you.

Close the suspension system by sliding the waist and
shoulder support clips together (Fig. 18, A).

NOTE: Make sure the weight of the unit is supported on the hips

by the waist support (Fig. 19, A).

If weight is not on hips, loosen the shoulder supports (Fig. 20,
A) and pull the waist support handle (Fig. 19, B) to tighten.
Adjust until the unit’s weight rests on the hips.

Pull the shoulder support handles to tighten the shoulder
supports (Fig. 18, B).

Releasing the Suspension System
1.

To loosen the shoulder supports, pull up on bottom tab of the
shoulder support buckles (Fig. 20, A).

Squeeze the top and bottom of the waist and shoulder
support clips to release the suspension system (Fig. 20, B).

HOLDING THE BLOWER
Before operating the unit, stand in the operating position (Fig. 21).

Check for the following:
• Operator is wearing proper clothing, such as boots, safety

glasses or goggles, ear/hearing protection, gloves, long pants
and long sleeve shirt.

• If the conditions are dusty, the operator is wearing a dust mask

or face mask.

WARNING:

To avoid serious personal injury, wear

goggles or safety glasses at all times when operating
this unit. Wear a face mask or dust mask in dusty
locations.

• The unit is in good working condition.
• The tubes are in place and secure.
OPERATING TIPS

• Assure the unit is not directed at anybody or any loose debris

before starting the unit.

• Verify that the unit is in good working condition. Make sure the

tubes are in place and secure.

• Always hold the unit securely when operating.
• To reduce the risk of hearing loss associated with sound level(s),

hearing protection is required.

• Operate power equipment only at reasonable hours— not early in the

morning or late at night when people might be disturbed. Comply
with times listed in local ordinances. Usual recommendations are 9:00
am to 5:00 pm, Monday through Saturday.

• To reduce noise levels, limit the number of pieces of equipment

used at any one time.

• To reduce noise levels, operate power blowers at the lowest

possible speed to do the job.

• Check your equipment before operation, especially the muffler,

air intakes and air filters.

• Use rakes and brooms to loosen debris before blowing.
• In dusty conditions, slightly dampen surfaces or use a mister

attachment when water is available.

• Conserve water by using power blowers instead of hoses for

many lawn and garden applications, including areas such as
screens, patios, grills, porches, and gardens.

• Watch out for children, pets, open windows or freshly washed

cars, and blow debris safely away.

• Use the full blower nozzle extension so the air stream can work

close to the ground.

• Clean up after using blowers and other equipment. Dispose of

debris appropriately.

• Use the trigger lock (Fig. 16) to keep the trigger depressed while

operating to make continuous operation easier.

APPLICATIONS
1

Use the blower for trees, shrubs, flower beds and hard-to-
clean areas.

Use the unit around buildings and for other normal cleaning
procedures.

Use the blower around walls, overhangs, fences and screens.

TRIGGER LOCK (Fig. 16)
To operate blower, squeeze the trigger to desired engine speed.
There is also a trigger lock which allows you to lock the trigger at a
constant engine speed for continuous operation.
To lock the trigger:
1. Squeeze and hold the trigger (Fig. 16).
2. Press and hold the trigger lock (Fig. 16).
3. Release the trigger.
4. Release the trigger lock to lock the trigger.
To release the trigger lock:
Squeeze and release the trigger, and the lock should disengage.

Fig. 18

WARNING:

To prevent serious personal injury or

damage to the unit, make sure blower tubes are in
place before you operate the unit.

Fig. 20

Fig. 19

Fig. 21