Valco Baby Spark - Manual (Page 7)

• Release the 4 buckles (a) beneath the seat
at both ends.
• Unzip the footwell (b)
• Push down on the seat surface to create the
bassinet interior.
Install the bassinet lining with ERGO Base
• Place the lining over the bassinet interior and
align the openings in the lining with the bassinet
housing and hood connection sites (c).
• Secure the lining over the bassinet sides to
the Velcro tabs located on the bassinet outer
body.
• Reinstall the hood and bumper bar.
• Attach the bootcover/apron to the open foot
of the bassinet, locating and securing to the
snaps at the side of the bassinet body.
To convert your bassinet to a stroller seat.
• Reverse the process out lined previously
• Remove the apron and lining
• Zip up the footwell
• Buckle all support straps beneath the seat
• Install the hood and bumper bar
IMPORTANT MATTRESS WARNING
Unlike cribs that have rigid sides, the bassinet
mattress is specially designed to prevent
suffocation. The mattress is designed to be
a snug fit and should not exceed 30mm in
thickness. Using a thicker or different sized
mattress may allow a child’s head to Get
between the mattress and the side of the
bassinet causing suffocation. To help prevent
suffocation from entrapment, USE ONLY THE
MATTRESS PROVIDED.
NEVER use additional mattress or padding.
Use only the fitted sheet provided.
9>BUMPER BAR
Insert each side of the bumper bar fitting into
the corresponding housing (a) in the seat
frame until you hear it click into place.
The bumper bar can be opened as a “gate” for
easy access pressing on one of the release
buttons (b) and lifting the side out of the
housing. For full removal, repeat this process
for the other side.
10>HOOD
Locate the hood stud fixtures found on either
side of the stroller, and align hood clamp to
studs. Attach clamp onto frame (a).
Your SPARK hood is designed to provide
maximum shade and comfort for your child by
incorporating our EXPANDA HOOD section.
To increase/decrease the hood size
Open the EXPANDA HOOD section fully
using the zip. Gently pull your hood forward;
extending it as far as is required.
When no longer needed, fold the EXPANDA
HOOD backward, allowing it to fold in on itself.
Gently zip the section closed being mindful not
to catch any of the fabric in the zipper teeth.
11>HARNESS
To secure your child in the harness:
Overlap buckles and so that they fit together to
form one complete buckle (a).
Insert the completed buckle into the Buckle
Housing (b) until it engages securely in
place(c).
To open your harness:
Push down on both Buckle Prongs (d).
Simultaneously press the release button in the
centre of the buckle (e).
Lift the buckles from the Buckle Housing (f).
IMPORTANT WARNING: AVOID SERIOUS
INJURY FROM FALLING OR SLIDING OUT.
ALWAYS USE SEAT BELT.
12>BRAKES
Press down on the long leg of the brake lever
(a) located on the rear axle to simultaneously
engage the brake in both rear wheels.
To release, press down on the shorter leg with
your foot.
IMPORTANT WARNING: ALWAYS TEST
THAT THE BRAKES ARE SECURELY
DISENGAGED BEFORE US E.
13>BOOTCOVER
Attach the bootcover/apron to the open foot of
the bassinet or seat, locating and securing to
the snaps at the side of the bassinet body.
14>FOLDING
Your Zee Spark can be folded with the seat in
facing in either direction as well as in bassinet
mode.
• Release the handle by simultaneously lifting
the triggers (a).
• Swing the handle over the seat/bassinet
body. As it passes the central pivot joint (b) the
lower frame will automatically release and the
stroller will fold down completely.
• The chassis will lock in the closed position
automatically.