Crestron cen-ups1250 uninterruptible power supply – Crestron electronic CEN-UPS1250 User Manual

Page 2

Crestron Electronics, Inc. 15 Volvo Drive

Rockleigh, NJ 07647

Tel: 800.237.2041 / 201.767.3400

Fax: 201.767.1903

www.crestron.com

Specifications subject to change without notice. Doc.4853 08/07

All brand names, product names and trademarks are the property of their respective owners.

Crestron CEN-UPS1250 Uninterruptible Power Supply

INCLUDED ACCESSORIES

CEN-UPS1250-BTP

Internal Battery Pack

Filtering: Full-time multi-pole noise filtering, 5% IEEE surge let-thru, zero clamping
response time, meets UL 1449 Dataline protection
Voltage Regulation: Performs voltage boost or trim to maintain 120V nominal output
Maximum Output Current: 12 Amps per outlet, 12 Amps total

Power Requirements

Input Voltage: 92 to 142 Volts AC, 120 Volts nominal
Input Frequency: 47 to 63 Hz
Maximum Input Current: 12 Amps (when fed from 15 Amp circuit)

Battery

Internal Battery: (4) 12 Volt, 9Ah maintenance-free sealed lead-acid w/suspended
electrolyte, Crestron model CEN-UPS1250-BTP included
Backup Runtime: ~12 minutes @ half load (625W), ~2.7 minutes @ full load (1250W)
Recharging Time: ~8 hours typical to 90% capacity following a discharge to shutdown
@ half load
Battery Life: 2 to 5 years under normal use

Ethernet

10BaseT/100BaseTX, auto-switching, auto-negotiating, autodiscovery, full/half duplex,
TCP/IP, UDP/IP, CIP, SNMP, 128-bit SSL encryption, IEEE 802.3U compliant

Connectors

BANK 1 – DIGITAL DEVICES: (5) NEMA 5-15R female, grounded AC power outlets,
switched; includes noise filtering and protection for digital devices such as control
systems, power supplies, touchpanels, and media servers

BANK 2 – DISPLAYS: (2) NEMA 5-15R female, grounded AC power outlets, switched;
includes noise filtering and protection for display devices such as LCDs, plasmas, and
projectors

BANK 3 – ANALOG DEVICES: (2) NEMA 5-15R female, grounded AC power outlets,
delayed-switched; delayed turn-on, adjustable 0 to 10 seconds; includes noise filtering
and protection for analog devices such as Adagio control systems and tuners

BANK 4 – HI-CURRENT DEVICES: (2) NEMA 5-15R female, grounded AC power outlets,
delayed-switched; delayed turn-on, adjustable 0 to 10 seconds; includes noise filtering
and protection for high-current devices such as amplifiers

EXTERNAL BATTERY: (1) Connector for optional external battery, sold by APC*

SERVICE PORT: (1) USB Type B female, used for factory configuration only

TELCO IN: (1) 4-pin RJ11 female, dual-line telephone line connection
TELCO OUT: (2) 4-pin RJ11 female, protected dual-line telephone/modem connections
CABLE IN: (1) F-type coaxial, female, coaxial cable or antenna source connection
CABLE OUT: (1) F-type coaxial, female, protected TV/receiver or modem connection
SATELLITE IN: (1) F-type coaxial, female, coaxial cable or antenna source connection
SATELLITE OUT: (1) F-type coaxial, female, protected TV/receiver or modem connection

COMPUTER: (1) USB Type B female, USB computer console port (cable included)

LAN: (1) 8-wire RJ45 with 2 LED indicators, 10/100BaseT Ethernet port
Green LED indicates link status, yellow LED indicates Ethernet activity

G: (1) Binding post, chassis ground lug

92-142V~12A 47-63Hz: (1) IEC-320 C14 chassis plug, line power input
Mates with 10 ft (3.05 m) power cord, included

ENV PROBE: 6-pin mini-DIN, female
Connection for external temperature/RH sensor, included

Buttons

SETUP: (1) Sequences through various configuration settings and operations
STATUS: (1) Sequences through display of various electrical and environmental
measurements, operational status, battery condition and other system information

, V: (2) Used to adjust configuration settings up/down or on/off

Power/Standby: (1) Turns all output banks on/off, forces cold-start to battery when held

CIRCUIT BREAKER (rear): Disrupts power to all outputs in case of an overload condition,
press to reset
RESET (rear): (1) Red miniature pushbutton, resets communications board

Display

Vacuum fluorescent, (2) lines, (20) characters per line

LED Indicators

BATT IN USE: (1 red) Indicates output power is being fed from battery backup
ON LINE: (1 green) Indicates a working connection to the control system
DELAY AMP: (1 green) Indicates BANK 4 – HI-CURRENT DEVICES output is turned on
REGULATING: (1 green) Indicates voltage regulation is operating to compensate for a
high or low line voltage condition
LOW BATT: (1 red) Indicates remaining backup time has fallen below a preset amount,
adjustable from 2 to 26 minutes
AC PWR OK: (1 green) Indicates the line input voltage is within the acceptable operating
range of 92V to 142V
FILTERING: (1 green) Indicates that the EMI and RFI noise reduction circuit is active
OVERLOAD: (1 red) Indicates there is too much load connected to the output
WIRING FAULT (rear): (1 red) Indicates a missing ground, overloaded neutral, or
reversed polarity at the line power input

Alarm

Audible alarm indicates when in backup mode, when battery is low, and when overloaded

Environmental

Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)

Enclosure

Chassis: Steel, black matte powder coat finish
Cooling: Microprocessor-controlled ultra-quiet rear-facing fan, vented sides
Faceplate: Extruded aluminum, black matte powder coat with polycarbonate label overlay
Mounting: Freestanding or 3U 19-inch rack-mountable, rack must be 4-post type up to
28-inch maximum depth (removable feet and rack mount kit included)

Dimensions

Height: 5.20 (13.21 cm) without feet
Width: 17.03 in (43.26 cm), 19.0 in (48.26 cm) with ears
Depth: 19.00 in (48.26 cm)

Weight

62.0 lb (28.18 kg)

American Power Conversion Corp. (APC), W. Kingston, Rhode Island, US;

Website: www.apc.com.

Rear View