RCBS Carbide Replacement Cutter for Trim Pro 3-way Cutter - Manual

CARBIDE
REPLACEMENT
CUTTER FOR TRIM PRO
3-WAY CUTTER
LIMITED LIFETIME WARRANTY
Your Carbide replacement cutter for Trim Pro 3-Way Cutter is warranted
to be free from defects in material or workmanship for as long as the
original owner owns it. This warranty is extended only to the original
consumer purchaser. This warranty excludes any electrical components
or products. All RCBS products are intended for non-commercial use by
hobbyists. Any other use of these products will void the warranty.
Should you believe that your Carbide replacement cutter for Trim Pro 3-
Way Cutter is defective in material or workmanship, you must return the
Carbide replacement cutter for Trim Pro 3-Way Cutter to Ammunition
Accessories Inc. through its Oroville operation (hereinafter “Oroville
Operations”) postage paid for evaluation. If defective, the product will be
repaired or replaced at Oroville Operations’ option, at no charge.
Send a dated proof of purchase to Oroville Operations for return shipping
and handling, along with the Carbide replacement cutter for Trim Pro 3-
Way Cutter to:
Ammunition Accessories Inc.,
Oroville Operations
605 Oro Dam Blvd East
Oroville, California 95965
Warranty services cannot be provided without meeting the above
requirements.
THIS LIMITED LIFETIME WARRANTY DOES NOT COVER DEFECTS
OR DAMAGE RESULTING FROM: CARELESSNESS, MISUSE,
COMMERCIAL USE, ABUSE, IMPROPER INSTALLATION,
MODIFICATION, OR NORMAL WEAR AND TEAR. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS
LIMITED LIFETIME WARRANTY. OROVILLE OPERATIONS IS NOT
LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF
THE PRODUCT AND UNDER NO CIRCUMSTANCES SHALL
OROVILLE OPERATIONS BE LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES. HOWEVER, SOME STATES DO NOT
ALLOW LIMITATIONS ON INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
The above warranty provides the sole and exclusive warranty available
to the customer in the event of a defect in material or workmanship in the
Carbide replacement cutter for Trim Pro 3-Way Cutter. This warranty
gives you specific legal rights, and you may also have other rights which
vary from State to State.
SAFETY
Reloading is an enjoyable and rewarding hobby that can be conducted
safely. But, as with any hobby, carelessness or negligence can make
reloading hazardous. This product has been designed from the
beginning with the user's safety in mind. When reloading, safety rules
must be followed. By observing these rules, the chance of a hazardous
occurrence causing personal injury or property damage is minimized.
GENERAL
• Use all equipment as the manufacturer recommends. Study the
instructions carefully and become thoroughly familiar with the
operation of the product. If you do not have written instructions,
request a copy from the equipment manufacturer.
• Do not take short cuts. Attempting to bypass established procedures
is an invitation to an accident.
• Observe "good housekeeping" in the reloading area. Keep tools and
components neat, clean and orderly. Promptly and completely clean
up primer and powder spills.
• Reload only when you can give your undivided attention. Do not
reload when fatigued or ill, or under the influence of medications or
alcohol.
• Develop a reloading routine to avoid mistakes which may prove
hazardous. Do not rush - load at a leisurely pace.
• Always wear adequate eye protection to protect your eyes from flying
particles. You assume unnecessary risk when reloading without
wearing safety glasses.
LOADING DATA
• Use only laboratory tested reloading data. We highly recommend the
current SPEER Reloading Manual.
• OBSERVE ALL WARNINGS ABOUT THE USE OF MAXIMUM
LISTED LOADS
INTRODUCTION
The Carbide replacement cutter for Trim Pro 3-Way Cutter was
designed to provide a lifetime of use and to produce clean and
consistent cutting.
DISASSEMBLY
Disassemble your existing 3-Way Cutter to remove the Standard
Cutter Head.
1. Loosen the Outside Deburring Cutter Setscrew (D) and rotate
Thumb Screw (B) counter clockwise to remove the Outside
Deburring Cutter (C) from the 3-Way Cutter Holder (A).
2. Loosen the 8-32 x 1/8 Setscrew (I) and remove the Standard
Cutter Head (E).
3. Remove the 8-32 x 1/8 Setscrew (G), 6-32 x 3/8 Setscrew
(H) and the Outside Chamfering Pilot (F) from the Standard
Cutter Head (E).
Thumb Screw
B
Outside Deburring
Cutter C
Outside Deburring
Cutter Setscrew
D
Standard Cutter
Head E
Carbide Cutter
Head J
Chamfering
Pilot F
8‐32 x 1/8
Setscrew
6‐32 x 3/8
Setscrew
H
3‐Way Cutter Holder
A
8‐32 x 1/8
Setscrew I
G
Photo 1
ASSEMBLY
Reassemble the 3-Way Cutter with the new Carbide Cutter
Head.
1. Insert Chamfering Pilot (F), 6-32 x 1/8 Setscrew (H) and 8-32
x 1/8 Setscrew (G) into the Carbide Cutter Head (J). The 6-32 x
3/8 Setscrew (H) is used to adjust the amount of inside case
mouth chamfer. The 8-32 x 1/8 Setscrew (G) is used to secure
item the Chamfering Pilot (F). Use a sized and de-primed case,
ready to be trimmed, and place the case mouth over the
Chamfering Pilot (F).
2. Make appropriate adjustments to the 6-32 x 3/8 Setscrew (H)
to allow the case to rest on the cutting flutes of the Carbide
Cutter Head (J). Once set, remove case and apply downward
pressure to the nose of the Chamfering Pilot (F). Secure the
Chamfering Pilot (F) in place with the 8-32 x 1/8 Setscrew (G).
Ensure cutter orientation is similar to that in Figure 1. Final
adjustments will be discussed later.
3. Insert the assembled Carbide Cutter Head (J) into the 3-Way
Cutter Holder (A), ensure the back of the cutter bottoms out
against the 3-Way Cutter Holder (A) and orientation of cutter is
similar to what is shown in figure 1. Secure the assembled
Carbide Cutter Head (J) in place with the 8-32 x 1/8 Setscrew (I)
and make sure the 8-32 x 1/8 Setscrew (G) is accessible, for
adjustment, as shown in Photo 2.
4. Insert the Outside Deburring Cutter (C) into the 3-Way Cutter
Holder (A). Use case from step one, place over the Chamfering