Bushnell 11-9000 - Manual (Page 4)

6
7
QUICK GUIDE: BUSHNELL TRAIL SENTRY 11-9000
5. The “key” icon will blink next, press ENTER and enter any four digit password of your choice (to keep using the default “0000”,
just press ENTER 4 times) by using the UP/DOWN buttons to change each digit and using ENTER to step to the next digit. When
finished, press ENTER if you want to return to the date/time setup menu, or press and hold the MENU button at any time to exit
all setup menus and return to normal operation.
6. In normal operating mode, the display will only show the still photo or movie clip icon in the lower left corner, an SD card
icon on the lower right, and one or more digits that indicate how many photo or movie files have been stored on the card. To test
the camera operation, wave your hand in front of the lens and PIR (passive infrared/motion) detector, while looking at the LCD
display. Every time an “event” is detected, the display will indicate “Plr”, “EVNT”, “rECd” in turn, and the event is recorded on the
SD card as a new line in a text file, including the date and time of the event. As long as events are being detected, a new still photo
or movie clip (as set in the menu) will be recorded every 30 seconds, indicated on the display by “Plr”, “SnAP”, then “SAVE”.
Note: for movie clips, the display will stay on “SnAP” for the 15 sec duration of each movie.
7. Thread the strap through the slots on the back of the Sentry and attach the buckles, then strap it onto a suitable tree, making
sure the strap is tight and the camera is aimed at the area you wish to observe. Turn on the camera (make sure a new or empty SD
card has been inserted) and leave the area-there is a 60 second delay after power on before the first photo is taken. The flash will
fire automatically at night for still photos, but not movies, so they will be dark unless the area is well lit by the moon or another
light source. Batteries typically last 30 days or more, depending on how often the Sentry is activated, how often the flash fires,
ambient temperature, etc..
8. Pressing the Up/Down buttons during normal operation will switch the display between showing # of photos stored and # of
events recorded. To look at your captured photos, make sure the power is off, and remove the SD card by pushing down lightly
on the top edge of the card-it will pop up for removal. Use an SD card reader with any PC or Mac (or the Bushnell Trail Scout
Viewer) to view, copy, or delete the photos (standard JPG files) and movies (AVI files) inside the “DCIM/100MEDIA” folder on
the card. Double click on an individual file to see it, or open the files with the photo software of your choice. The event log is the
.TXT file, just double click to open and view with your default software for standard plain text files.
Digital Trail Sentry Specifications
Image Sensor 1/4” CMOS VGA sensor with images enhanced to 1.3MP files via software
interpolation
Lens F/3.5, effective focal length 42mm. Sight range: 45 degrees
Flash High power electronic Incandescent Flash. Range: 15 ft.
PIR Sensor Low noise, high sensitivity passive infrared sensor. Range: 45 ft.
Motion LED Indicator Yes
Display Monochrome LCD. Auto-off: 3 min. 2-digit event and image display.
File Format Still image JPG 1280x960 pixels (SXGA). Movie clips AVI 320x240 pixels per
frame, 1 frame per second rate, 15 second length. DCF ver. 1.0 file management.
Exposure Auto
White Balance Auto
Power Supply 4 x “D” size alkaline batteries.
Battery Life Approximately 30 days (dependant on temperature, camera activity and flash
usage)
Card Compatibility Verified compatible with up to 1 GB capacity secure digital (SD)cards. The use of
MMC cards is not recommended.
User Password Yes, available range: 0000 to 9999 (Default setting = 0000)