Nipros LVM-89W - Manual

LVM-89W
For using LVM-89W.
Before operating your LVM-89W, please read this manual thoroughly and remain it for future reference.
■Outsideview and Dimensions / Names and Functions of Parts
Operating
Instructions 8.9 HDMI View Finder Monitor
front
(bottom)
left side
connector panel
(right side)
COLOR INPUT RGB MARKER
MONO
16:9
4:3
PEAKING
HD/Y
HD/B-Y
HD/R-Y
CMP IN
CMP OUT
TALLY IN
MONI IF
DC 12V IN
Screen 8.9 inch liquid crystal display (196(H) 115(V) mm )
FRONT GREEN TALLY indicator
GREEN TALLY indicator on the front panel lights up when the tally signal(2∼4V=GREEN) is input
to the TALLY IN connector on the connector panel.
The front tally indicators (GREEN and RED) are dimmed by the tally dimming select switch.
RED TALLY indicator on the front panel lights up when the tally signal(4∼ V=RED) is input to the
TALLY IN connector on the connector panel or the tally signal(0V=ON, OPEN=OFF) is input to the
MONI IF connector.
The front tally indicators (GREEN AND RED) are dimmed by the tally dimming select switch.
FRONT RED TALLY indicator
TALLY indicators on the front and rear panels can be selected by the switches as follows.
FRONT TALLY and REAR TALLY dimming select switch
H : The tally lamp lights up brightly.
L : The tally lamp is dimmed to the lower brightness.
OFF : The tally lamp is prevented from lighting.
GREEN TALLY indicator on the rear panel lights up when the tally signal(2∼4V=GREEN) is input
to the TALLY IN connector on the connector panel.
The rear tally indicators (GREEN AND RED) are dimmed by the tally dimming select switch.
REAR GREEN TALLY indicator
RED TALLY indicator on the front panel lights up when the tally signal(4∼ V=RED) is input to the
TALLY IN connector on the connector panel or the tally signal(0V=ON, OPEN=OFF) is input to the
MONI IF connector.
The rear tally indicators (GREEN and RED) are dimmed by the tally dimming select switch.
REAR RED TALLY indicator
Function buttons
COLOR INPUT RGB MARKER
MONO
16:9
4:3
PEAKING
INPUT button selects signal : input connector
COMP 1 HD component : HD/Y, HD/B-Y, HD/R-Y (BNC) connector
↓
CVBS 1 composite : CMP IN (BNC) connector
↓
COMP 2 NC
↓
CVBS 2 composite : MONI IF (6-pin) connector
↓
HDMI HDMI : HDMI connector
↓
RGB button : Pressing RGB select button selects the Blue only, green only, or red only as follows.
COLOR/MONO button : Pressing COLOR/MONO selects button select the color or monochrome.
PEAKING (on/off) button : Pressing PEAKING button selects the peaking function ON or OFF.
The adjustment of peaking level (when PEAKING is ON) is enabled on the menu.
16:9 / 4:3 select button : pressing 16:9/4:3 button selects the frame size 16:9 or 4:3.
MARKER (select) button : Pressing Marker button selects the marker in sequence as follows.
INPUT select button : Selects the input signal connected to the HD(Y/B-Y/R-Y) component, CMP IN (composite signal
input), MONI IF(8-pin, composite signal input), and HDMI connector.
By pressing INPUT button select the input signal in sequence. The selected signal name is displayed on the screen.
no marker
↓
16:9 (90%)
↓
16:9 with center marker
↓
4:3
↓
4:3 wiyh center marker
↓
all markers
↓
Full color
↓
BLUE ONLY
↓
GREEN ONLY
↓
RED ONLY
↓
MARKER button selects RGB button selects
MENU/ - / + (menu select and entry) buttons
Pressing MENU (select) button selects the settings from the menus displayed on the screen in sequence as follows.
Pressing - / + (entry) button adjusts each setting.
When Reset is selected, pressing - / + button resets all settings to standard value(50).
MENU button selects - / + button adjusts
Brightness ( 0 - 50(reset) -100 )
↓
Contrast ( 0 - 50(reset) -100 )
↓
Peaking ( 0 - 50(reset) -100 )
↓
Sharpness ( 0 - 50(reset) -100 )
↓
Saturation ( 0 - 50(reset) -100 )
↓
Hue ( 0 - 50(reset) -100 )
↓
Reset ( Pressing resets all settings to 50 )
↓
HD/Y, HD/B-Y, HD/R-Y connectors (BNC type) : used for HD component signal input )
CMP IN connector (BNC type) : used for composite video signal input)
CMP OUT connector (BNC type) : used for composite video signal output)
TALLY IN connector (BNC type) : used for tally signal input)
MONI IF connector (6-pin) : used for monitor interface input)
DC 12V IN connector (XLR 4-pin) : used for DC 12V power supply input)
HDMI connector : used for HDMI signal input)
1/4 inch screw hole : used to fix to a tripod, etc.
217
35
14
9
NIPPON VIDEO SYSTEM accepts no liability whatever for damages arising from improper use not conforming
to the instructions in the instruction manuals.
NIPPON VIDEO SYSTEM accepts no liability whatever for incidental damages arising out of the use or inability
to use the product, including, but not limited to, damage to the camera, etc., corruption or loss of data, lost
business revenue or suspension of business operations.
TM