B&K CT610 - Manual (Page 3)

MZ-128 Remote Control
1
POWER
1 2 3
4
7
5
8
0
6
9
ENTER
IN 8 IN 8
TUNE-
SAVE MENU
EXIT
LOUD
OFF MUTE
IN 9 IN 9
+10
AM M T+ S+
FM V+ T- S-
B & K Components, Ltd.
Model MZ-128
SEL
ENTER
VOLUME PRESET
ON/OFF
ON
B&K
B+
B-
Õ
®
° ¯
IN 1 IN 1 IN 2 IN 2 IN 3 IN 3
IN 5 IN 5 IN 4 IN 4 IN 6 IN 6 IN 7 IN 7
ZONE
VIDEO + VIDEO +
BASS TREBLE SOURCE ST/M
LOUDNESS
DEDICATED
D-IN
TUNE+ STA- STA+
UP
DOWN
L
E
F
T L
E
F
T
R
I
G
H
T
R
I
G
H
T
B & K CT Series MZ-128 Remote Controller Reference Sheet
The MZ-128 Remote Controller has multiple useful functions:
1) The MZ-128 Remote Controller may be used to control and setup a CT610/600310/300.
2) The
learning keypads etc...
3) The may be set to source code sets 000-128
and 999.
MZ-128 may be used as a source of IR for use in programming
MZ-128
the B & K IR functions listed below, for
Setup the MZ-128 to use a discrete B & K code set:
1) Install 4 AAA batteries into the remote. Observe polarity.
2) Press and hold the B & K and MUTE buttons simultaneously for two seconds. The LED will
light up solid red and stay illuminated.
3) Firmly press the desired B & K three digit code set. Always use three digits (i.e. 0-1-1 Zone A)
4) Press the B & K button again to confirm setup. The red LED will blink three times when the IR
code has been successfully programmed.
CODE SET 000-128
MZ-128 BUTTON B & K IR FUNCTION
[POWER STATE]
[VOLUME]
[TONE CONTROL]
[INPUT SOURCE]
[FAVORITE PRESET]
MZ-128 BUTTON B & K IR FUNCTION
[TUNER]
[NAVIGATION]
[NUMERIC]
B&K POWER ON
POWER POWER TOGGLE
OFF POWER OFF
MUTE MUTE TOGGLE
VOLUME MASTER VOL UP
VOLUME MASTER VOL DOWN
B+ BASS UP
B- BASS DOWN
T+ TREBLE UP
T- TREBLE DOWN
LOUD LOUDNESS TOGGLE
S+ SOURCE UP
S- SOURCE DOWN
V+ VIDEO SOURCE UP
D-IN ZONE DEDICATED IN
AM TUNER AM
FM TUNER FM
IN 1 IN 1 OR [V1]
IN 2 IN 2 OR [V2]
IN 3 IN 3 OR [TV]
IN 4 IN 4 OR [DVD]
IN 5 IN 5 OR [CD]
IN 6 IN 6 OR [SAT]
IN 7 IN 7 OR [TAPE]
IN 8 IN 8 OR [V4]
IN 9 IN 9 OR [V5]
PRESET FAVORITE PRESET UP
PRESET FAVORITE PRESET DN
AM SELECT THE AM BAND
FM SELECT THE FM BAND
TUNE + TUNE FREQUENCY UP
TUNE - TUNE FREQUENCY DOWN
STA + TUNER FAV PRESET UP
STA - TUNER FAV PRESET DOWN
M STEREO / MONO
MENU MENU UP/DOWN LEVEL
LEFT LEFT OR BALANCE (L)
RIGHT RIGHT OR BALANCE (R)
SEL/ENTER SELECT OR ENTER
UP UP
DOWN DOWN
SAVE SAVE
EXIT TOTAL EXIT FROM ALL MENUS
ZONE ZONE SELECT
0 0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
+10 +10
CODE SET 999
MZ-128 BUTTON
B & K IR FUNCTION
[B & K ALL COMMANDS]
ON/B & K/POWER ALL B & K POWER ON
OFF
ALL B & K POWER OFF
VOLUME ALL B & K VOLUME UP
VOLUME ALL B & K VOLUME DOWN
0 ALL B & K VOLUME 0 DB
2 ALL B & K VOLUME -20 DB
4 ALL B & K VOLUME -40 DB
6 ALL B & K VOLUME -60 DB
MUTE ALL B & K MUTE TOGGLE
B & K
MZ-128 Default Factory Code-Set is: 0-0-0 Whole House Control
Code-Set 128 Simply Explained
Code-Set 128 is a special code-set which
allows individual control of the Hardware Zone
that the IR Data is received by. It will not function
when received by the unit’s front panel. I.e., Two
keypads are plugged into Zone A & B’s Control
I/O Ports, when the remote comes into IR view
of the keypad in Zone A, the 128 Code-set
remote will only control Zone A, when in Zone A.
Take that same remote into Zone B and it will
only control Zone B.