Behringer EUROPORT Ultra-Compact 900-Watt 8-Channel Portable PA System with Digital Effects and FBQ Feedback Detection EPA900 - Manual (Page 5)

5 EUROPORT EPA900 User Manual
Before You Get Started 1.
Shipment 1.1
Your EPA900 was carefully packed at the factory, and the packaging was
designed to protect the unit from rough handling. Nevertheless, we recommend
that you carefully examine the packaging and its contents for any signs of
physical damage that may have occurred during transit.
If the unit is damaged, please do NOT return it to BEHRINGER. ◊
Instead, notify your dealer and the shipping company immediately.
Otherwise, claims for damage or replacement may not be honored.
Always use the original packing carton to prevent damage during ◊
storage or transport.
Make sure that no children are left unsupervised with the unit or ◊
its packaging.
Please ensure proper disposal of all packing materials. ◊
Initial operation 1.2
Be sure that there is enough space around the unit for cooling. To avoid
overheating, please do not place the EPA900 near radiators and other equipment
emanating heat.
Blown fuses must be replaced by fuses of the same type and rating! ◊
Please refer to the “TECHNICAL SPECIFICATIONS” section for the correct
rating. To avoid an electric shock, turn off and unplug the unit before
replacing the fuse. For more information, please see Chapter 3.8
and Figure 3.9.
The mains connection is made using the enclosed power cord and a standard IEC
receptacle. It meets all of the international safety certification requirements.
Before connecting the unit to the mains, please check that it is set to ◊
the correct supply voltage.
You have to use another fuse if you set the unit to another supply ◊
voltage. The correct value is specified in Chapter “Specifications”.
Please make sure that all units have a proper ground connection. ◊
For your own safety, never remove or disable the ground
conductor from the unit or of the AC power cord. The unit shall
always be connected to the mains socket outlet with a protective
earthing connection.
Please ensure that only qualified people install and operate the ◊
mixing console. During installation and operation, the user must have
sufficient electrical contact to earth, otherwise electrostatic discharges
might affect the operation of the unit.
The sound quality may diminish within the range of powerful ◊
broadcasting stations and high-frequency sources. Increase the
distance between the transmitter and the device and use shielded
cables for all connections.
Online registration 1.3
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contact
the BEHRINGER retailer from whom the equipment was purchased. Should your
BEHRINGER dealer not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information is included in the
original equipment packaging (Global Contact Information/European Contact
Information). Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area of our website
(http://behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and efficiently.
Thank you for your cooperation!
Installation 2.
The EPA900 mobile PA system consists of two loudspeakers and a powered mixer
that easily join into a portable, wheeled unit for easy transportation. In the
following sections, you will find out how to set up and start up the PA system.
Setup preparations 2.1
Follow the instructions to ensure straightforward and reliable operation of
the EPA900.
Open the upper latch. 1.
Open the latches on the sides of the PA unit by pressing and then 2.
lifting them.
With one hand, grab hold of the recessed handle above the latch on the side 3.
of the loudspeaker and hold the upper handle with the other hand.
Then, carefully remove the loudspeaker sideways from the mixer.
Be careful to prevent the loudspeaker from accidentally falling on ◊
your foot.
Repeat Step 3 for the second loudspeaker. 4.
Place the mixer in an upright position. 5.
To assemble the PA unit for transportation, perform the steps in the ◊
reverse order.
(2)
(1)
(3)
Fig. 2.1: EPA900 setup