Black & Decker VPX2102 - Manual (Page 10)

10
FILTERS
FIG. J, K - To remove the filters, twist the outer (plastic) filter in a clockwise direction.
Shake or lightly brush any loose dust off the outer filter. Remove the inner filter and
shake, tap or lightly brush outside surface to remove loose dust. Both filters can be
rinsed as shown in figure L. CAUTION: Filter must be dry before re-assembling.
Ensure both filters are in place before operating.
FIG. L - Wash the filters using warm, soapy water and ensure that they are completely
dry before using it again. The cleaner the filters are, the better the product will perform. It
is very important that the filter is correctly in position before use. The dust bowl can also
be washed in warm soapy water. CAUTION: Filters must be dry before re-assembling.
IMPORTANT: Maximum dust collection will only be obtained with clean filters and an
empty dust bowl. If dust begins to fall back out of the product after it is switched off, this
indicates that the bowl is full and requires emptying.
FIG. M - Never immerse the product in water. A damp cloth and soapy water should be
used to clean the exterior of the motor section. Always ensure the product is completely
dry before re-use or storing.
ACCESSORIES
A crevice tool is built-in to the nozzle and can be extended as shown in figure N by pulling
the extension piece until it locks into position.
The extension can be retracted by depressing the area at the back of the extension and
pushing the extension back into the nozzle. Additional accessories are stored on the
product (figure O) and are fitted into the nose of the product for use.
NOTE: Replacement filters can be purchased from most local/national retailers that sell
vacuums, or by calling 1-888-678-7278. Look for catalog number VF08 filter.
MAINTENANCE
Use only mild soap and damp cloth to clean the vac. Never let any liquid get inside the
vac; never immerse any part of the vac into a liquid.
NOTE: Make sure the vacuum is completely dry before using it.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service organizations, always using
identical replacement parts.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
lithium ion battery (or battery pack) indicates that the costs to recycle the
battery (or battery pack) at the end of its useful life have already been paid by Black &
Decker.
RBRC™ in cooperation with Black & Decker and other battery users, has established
programs in the United States to facilitate the collection of spent ion batteries. Help protect
our environment and conserve natural resources by returning the spent lithium ion battery
to an authorized Black & Decker service center or to your local retailer for recycling. You
may also contact your local recycling center for information on where to drop off the spent
battery.
RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service. Whether you need technical
advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow page directory under
"Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge
in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days
90521333 VPX2102 Hand Vac 8/2/07 7:44 AM Page 10