beautypg.com

Assembly package contents, Removing your old lavatory – Vigo VG09040K1 User Manual

Page 5

background image

5

ASSEMBLY

PACKAGE CONTENTS

BACK SIDE OF THE VANITY

WALL SCREW
LOCATION

Wall

Cabinet

Plastic anchor

Screw

5. For specific Faucet installation instructions refer to the Faucet manufacturer's
instruction guide. Connect supply line to faucet.

3. Silicone the lavatory to the vanity, align it and press down firmly.

1. Select the vanity location and mark holes on the wall for mounting screws.
Remove the vanity, drill holes, stick anchors. Securely screw unit to the wall. This

should be drilled into your 2"x6" backing material.

VANITY INSTALLATION

1

VANITY

PLASTIC ANCHOR - 2PC.

SCREW - 2PC.

4

4. Connect Trap to drain assembly. Vigo recommends installing the Vigo brand
corresponding sink and pop up. Figure #4 depicts the complete assembly of the
Vigo brand sink, vanity and pop up.

CARE AND MAINTENANCE

REQUIRED TOOLS

SAFETY TIPS

INSTALLATION

Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.

REMOVING YOUR OLD LAVATORY

Adjustable wrench

Plumber's putty or Caulking
Pipe tape
Flat screwdriver
Philips Screw Driver

To ensure that your installation project goes smoothly, please review these
instructions before proceeding.
Your new lavatory is designed for years of trouble-free performance.

Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals.

To protect against scratches, use felt, leather, or cork under all items placed on
the wood surface. Do not expose wood furniture to direct sunlight, drying heat
sources, or dampness. Dust frequently with a soft cloth in the direction of the
grain. Use only products specifically made for cleaning wood. Avoid using oily
polishes or waxes, or products containing silicone. Blot spills immediately with
a soft, damp cloth.

Turn off the water supply. This is done by closing the two shut-off valves
located under the lavatory.

If there are no shut-off valves leading to the lavatory, you must turn off the

water at the main valve. This is usually located in the basement, garage or near
the foundation on the outside of the house. It may also be near the water meter.
Check to be sure the water is off by turning on the faucet where you are
working until the water stops flowing.

If you have shut off the main valve in a two-story house or greater, you should

open the kitchen faucet and another faucet on the same level. Water will then
drain from the entire line. This will help avoid spills. Be sure and close the
faucets before you turn on the main valve again. Disconnect the drain pipes.
Take off as many sections as possible between the lavatory and the wall or
floor to facilitate removal. Place a basin under the work area to catch any water
that may still be in the drain.

Drill

Tape Measure
Tubing Cutter or Hacksaw
Caulking gun

Observe all local plumbing and building codes.
Risk of personal injury or product damage will occur if not handled in the proper
manner. Always consult your licensed contact with any questions or concerns.
Handle with care. Vitreous china/Glass/Acrylic can break or chip if the product is
handled carelessly.
Prior to installation, unpack the new vanity components and inspect it for
damage. Return the material to its protective carton until you are ready to install
it. Inspect the drain and supply plumbing. Replace if necessary.

2. For ease of installation it is recommended for you to install the faucet on the
sink/top at this point. If you are unable to do so at this point and have to install
the faucet at the completion of the vanity see page 6 as this is the needed drawer
removal steps for access for completion of installation.

NOT PROVIDED

TAIL PIECE

DRAIN NUT

TO DRAIN

WASHER

DRAIN ASSEMBLY

SOFT WHITE WASHER

POP UP TOP

INTERNAL BRASS PIECE (POP UP MECHANISM)

DO NOT OVER TIGHTEN THE DRAIN

!

POP UP DRAIN

RUBBER WASHER

SINK

OVERFLOW

(with overflow)

TAIL PIECE

DRAIN NUT

SOFT WHITE WASHER

TAIL PIECE NUT

WHITE PLASTIC WASHER

POP UP DRAIN TOP

RUBBER WASHER

SINK

INTERNAL BRASS PIECE
(POP UP MECHANISM)

OVERFLOW

WHITE PLASTIC WASHER