beautypg.com

Package contents, Removing your old lavatory, Assembly – Vigo VG0908K1 User Manual

Page 5

background image

5

PACKAGE CONTENTS

VANITY

VANITY BRACKETS
(2PC.)

PLASTIC ANCHOR
- 8PC.

SCREW - 8PC.

COVER - 1PC.

ASSEMBLY

7. For specific Faucet installation instructions refer to the Faucet manufacturer's
instruction guide. Connect supply line to faucet.

1. Once the product has been unpacked your first step will be to assemble the unit.

Select the vanity location and mark holes on the vanity for wall brackets and for
mounting screws (see holes on the back side of the vanity). Remove brackets, drill
holes, sink anchors and screw the brackets to the wall. This should be drilled into your
2"x6" backing material.

6. Connect Trap to drain assembly. Vigo recommends installing the Vigo brand
corresponding sink and pop up. Figure #6 depicts the complete assembly of the
Vigo brand sink, vanity and pop up.

4. Silicone the lavatory and to the vanity.

3. Loosen both adjusting screws in the vanity hanging unit. Hang up the vanity to the
wall brackets. Tighten adjusting screws.

Side wall of the vanity

Vanity bracket

Wall

Hanging unit

Adjusting screw

5. Install the drain assembly. Connect tailpiece to the drain.

Hook

3

6

CARE AND MAINTENANCE

REQUIRED TOOLS

SAFETY TIPS

INSTALLATION

Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.

REMOVING YOUR OLD LAVATORY

Adjustable wrench

Plumber's putty or Caulking
Pipe tape
Flat screwdriver
Philips Screw Driver

To ensure that your installation project goes smoothly, please review these
instructions before proceeding.
Your new lavatory is designed for years of trouble-free performance.

Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals.

To protect against scratches, use felt, leather, or cork under all items placed on
the wood surface. Do not expose wood furniture to direct sunlight, drying heat
sources, or dampness. Dust frequently with a soft cloth in the direction of the
grain. Use only products specifically made for cleaning wood. Avoid using oily
polishes or waxes, or products containing silicone. Blot spills immediately with
a soft, damp cloth.

Turn off the water supply. This is done by closing the two shut-off valves
located under the lavatory.

If there are no shut-off valves leading to the lavatory, you must turn off the

water at the main valve. This is usually located in the basement, garage or near
the foundation on the outside of the house. It may also be near the water meter.
Check to be sure the water is off by turning on the faucet where you are
working until the water stops flowing.

If you have shut off the main valve in a two-story house or greater, you should

open the kitchen faucet and another faucet on the same level. Water will then
drain from the entire line. This will help avoid spills. Be sure and close the
faucets before you turn on the main valve again. Disconnect the drain pipes.
Take off as many sections as possible between the lavatory and the wall or
floor to facilitate removal. Place a basin under the work area to catch any water
that may still be in the drain.

Drill

Tape Measure
Tubing Cutter or Hacksaw
Caulking gun

Observe all local plumbing and building codes.
Risk of personal injury or product damage will occur if not handled in the proper
manner. Always consult your licensed contact with any questions or concerns.
Handle with care. Vitreous china/Glass/Acrylic can break or chip if the product is
handled carelessly.
Prior to installation, unpack the new vanity components and inspect it for
damage. Return the material to its protective carton until you are ready to install
it. Inspect the drain and supply plumbing. Replace if necessary.

Holes for the mounting screws

32 1/8" to center of clip +/- 1/8"

1

2. For ease of installation it is recommended for you to install the faucet on the sink/top
at this point. If you are unable to do so at this point and have to install the faucet at the
completion of the vanity see page 6 as this is the needed drawer removal steps for
access for completion of installation. Also, it is recommended to cut support legs at the
same dimension you have picked for the vanity to be off the floor for extra support
while installing.

NOT PROVIDED

TAIL PIECE

DRAIN NUT

TO DRAIN

WASHER

DRAIN ASSEMBLY

SOFT WHITE WASHER

POP UP TOP

INTERNAL BRASS PIECE (POP UP MECHANISM)

DO NOT OVER TIGHTEN THE DRAIN

!

POP UP DRAIN

RUBBER WASHER

SINK

OVERFLOW

(with overflow)

TAIL PIECE

DRAIN NUT

SOFT WHITE WASHER

TAIL PIECE NUT

WHITE PLASTIC WASHER

POP UP DRAIN TOP

RUBBER WASHER

SINK

INTERNAL BRASS PIECE
(POP UP MECHANISM)

OVERFLOW

WHITE PLASTIC WASHER