Vigo VG09041K - Manual (Page 5)

5
ASSEMBLY
PACKAGE CONTENTS
BACK SIDE OF THE VANITY
WALL SCREW
LOCATION
6. Select the mirror location and
mark holes on the wall for
mounting bracket. Make sure
mounting brackets are level to
ensure that the mirror is
mounted straight. Drill holes,
sink anchors and secure screws.
Wall
Cabinet
Plastic anchor
Screw
5. For specific Faucet installation instructions refer to the Faucet manufacturer's
instruction guide. Connect supply line to faucet.
3. Silicone the lavatory to the vanity, align it and press down firmly.
1. Select the vanity location and mark holes on the wall for mounting screws.
Remove the vanity, drill holes, stick anchors. Securely screw unit to the wall. This
should be drilled into your 2"x6" backing material.
VANITY INSTALLATION
Mirror bracket
Wall
anchors
1
6
MIRROR
PLASTIC ANCHOR - 2PC. SCREW - 2PC.
VANITY
PLASTIC ANCHOR - 2PC. SCREW - 2PC.
MIRROR BRACKET
4
4. Connect Trap to drain assembly. Vigo recommends installing the Vigo brand
corresponding sink and pop up. Figure #4 depicts the complete assembly of the
Vigo brand sink, vanity and pop up.
CARE AND MAINTENANCE
REQUIRED TOOLS
SAFETY TIPS
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
REMOVING YOUR OLD LAVATORY
Adjustable wrench
Plumber's putty or Caulking
Pipe tape
Flat screwdriver
Philips Screw Driver
To ensure that your installation project goes smoothly, please review these
instructions before proceeding.
Your new lavatory is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals.
To protect against scratches, use felt, leather, or cork under all items placed on
the wood surface. Do not expose wood furniture to direct sunlight, drying heat
sources, or dampness. Dust frequently with a soft cloth in the direction of the
grain. Use only products specifically made for cleaning wood. Avoid using oily
polishes or waxes, or products containing silicone. Blot spills immediately with
a soft, damp cloth.
Turn off the water supply. This is done by closing the two shut-off valves
located under the lavatory.
If there are no shut-off valves leading to the lavatory, you must turn off the
water at the main valve. This is usually located in the basement, garage or near
the foundation on the outside of the house. It may also be near the water meter.
Check to be sure the water is off by turning on the faucet where you are
working until the water stops flowing.
If you have shut off the main valve in a two-story house or greater, you should
open the kitchen faucet and another faucet on the same level. Water will then
drain from the entire line. This will help avoid spills. Be sure and close the
faucets before you turn on the main valve again. Disconnect the drain pipes.
Take off as many sections as possible between the lavatory and the wall or
floor to facilitate removal. Place a basin under the work area to catch any water
that may still be in the drain.
Drill
Tape Measure
Tubing Cutter or Hacksaw
Caulking gun
Observe all local plumbing and building codes.
Risk of personal injury or product damage will occur if not handled in the proper
manner. Always consult your licensed contact with any questions or concerns.
Handle with care. Vitreous china/Glass/Acrylic can break or chip if the product is
handled carelessly.
Prior to installation, unpack the new vanity components and inspect it for
damage. Return the material to its protective carton until you are ready to install
it. Inspect the drain and supply plumbing. Replace if necessary.
2. For ease of installation it is recommended for you to install the faucet on the
sink/top at this point. If you are unable to do so at this point and have to install
the faucet at the completion of the vanity see page 6 as this is the needed drawer
removal steps for access for completion of installation.
NOT PROVIDED
TAIL PIECE
DRAIN NUT
TO DRAIN
WASHER
DRAIN ASSEMBLY
SOFT WHITE WASHER
POP UP TOP
INTERNAL BRASS PIECE (POP UP MECHANISM)
DO NOT OVER TIGHTEN THE DRAIN !
POP UP DRAIN
RUBBER WASHER
SINK
OVERFLOW
(with overflow)
TAIL PIECE
DRAIN NUT
SOFT WHITE WASHER
TAIL PIECE NUT
WHITE PLASTIC WASHER
POP UP DRAIN TOP
RUBBER WASHER
SINK
INTERNAL BRASS PIECE
(POP UP MECHANISM)
OVERFLOW
WHITE PLASTIC WASHER