MB QUART Nautic - Manual (Page 9)

6-Channel Amplifiers
NA540.6
8
6 Channel Full Range Stereo
1. Interconnect cable checklist: 3. Crossover frequency control checklist:
Connect the 6 Inputs of the amplifier to a Radio/CD with quality RCA cables. N/A for full range operation.
2. Filter Switch: 4. Line Level:
- 1/2CH: FLAT Refer to section “Setting up systems after installation for best performance.”
- 3/4CH: FLAT
-5/6CH: FLAT
5 Channel Operation 2. Filter Switch:
This illustration shows how to use your 6 channel amplifier as a 5 channel unit by taking - 1/2CH: FLAT
advantage of the mono bridging capability on all NAUTIC amplifiers. - 3/4CH: FLAT
- 5/6CH: LOW
1. Interconnect Cable Checklist: 3. Crossover frequency control checklist:
- 1/2CH & 3/4CH: Connect the Inputs of channel pair ½ to a suitable stereo source N/A for full range operation. 5/6CH set to 80Hz.
with quality RCA cables. Repeat these steps for 3/4CH. 4. Line Level:
- 5/6CH: Connect a mono line Input via Y-adapter from a mono source or single Refer to the section “Setting up systems after installation for best performance.”
Left or Right RCA from a stereo source. This has been detailed on previous pages 5.Speaker Connections:
Connect the subwoofer - to Ch6- and the subwoofer + to Ch5+. Connect the remaining
for reference.
speakers in standard stereo wiring to CH1/2 & CH3/4. IMPORTANT: Do not connect Left and Right stereo signals together to achieve a mono
signal as this will damage the output stage of the source and possibly the input stage of
IMPORTANT: Minimum final loudspeaker impedance presented to the amplifier is
the amplifier therefore voiding your warranty. 4-Ohms in mono operation and 2-Ohms in stereo operation.
P O W
E R IN
P U T
P O W E R IN
P U T
G N D
R E M
B A T T + 12
V
G N D
R E M
B A T T + 12
V
6C
H
5C
H
6C H
5C
H
4 C H
3C H
2 C H
1 C H
4 C H
3C H
2 C H
1 C H
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
B R ID
G E D
B R ID
G E D
B R ID
G E D
B R ID G E D
B R ID
G E D
B R ID
G E D
LINE OUTPUT DIAGNOSTICS
MODE
POWER
PROTECT CH-2
CH-1
CH-6 CH-4
CH-5 CH-3
CH-2
CH-1
2-CH 6-CH 4-CH
LINE INPUT
LEVEL FILTER FREQUENCY BASS EQ
6V .2V
HIGH LOW FLAT
40Hz 250Hz 0dB 9dB
CHANNELS 1 & 2
CHANNELS 3 & 4 CHANNELS 5 & 6
LEVEL FILTER FREQUENCY BASS EQ
6V .2V
HIGH LOW FLAT
40Hz 250Hz 0dB 9dB 6V .2V
HIGH LOW FLAT
40Hz 250Hz 0dB 9dB
LIN
E O U TP U T
LIN
E O U TP U T
D IA G N O S T IC S
D IA G N O S T IC S
M O D E
M O D E
P O W
E
R
P O W
E
R
P R O T E C T
P R O T E C T
C H -2
C H -2
C H -1
C H -1
C H -6
C H -6
C H -4
C H -4
C H -5
C H -5
C H -3
C H -3
C H -2
C H -2
C H -1
C H -1
2 -C H
2 -C H
6 -C H
6 -C H
4 -C H
4 -C H
L IN E IN
P U T
L IN E IN
P U T
LE V E L
LE V E L
FIL TE R
FIL TE R
FR E Q U E N C Y
FR E Q U E N C Y
BA SS E Q
BA SS E Q
6 V
6 V
.2 V
.2 V
H IG H
H IG H
L O W
L O W
F L A T
F L A T
40 H z
40 H z
25 0H z
25 0H z
0 d B
0 d B
9 d B
9 d B
C H A N N E L S 1 & 2
C H A N N E L S 1 & 2
C H A N N E L S 3 & 4
C H A N N E L S 3 & 4
C H A N N E L S 5 & 6
C H A N N E L S 5 & 6
LE V E L
LE V E L
FIL TE R
FIL TE R
FR E Q U E N C Y
FR E Q U E N C Y
BA SS EQ
BA SS EQ
6 V
6 V
.2 V
.2 V
H IG H
H IG H
L O W
L O W
F L A T
F L A T
40 H z
40 H z
25 0H z
25 0H z
0d B
0d B
9d B
9d B
6 V
6 V
.2 V
.2 V
H IG H
H IG H
L O W
L O W
F L A T
F L A T
40 H z
40 H z
25 0H z
25 0H z
0d B
0d B
9d B
9d B
FEATURES:
- 3 Sets of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS BOOST: Adjustable 45Hz bass boost from 0dB to 9dB
- X-OVER: Selects internal crossover functions
- FLAT: Bypasses all crossovers for full frequency operation
- LOW: Selects the built in LOW PASS filter
- HIGH: Selects the built in HI PASS filter
- POWER LED: Indicates the powered up and turned on condition
- PROTECTION LED: Indicates a high voltage, low voltage, short circuit,
hard clip, over heating or DC fault condition.
- MODE: “2” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 and 5/6 through
1/2 inputs. “4” indicates connecting 2 sets of RCA’s to 1/2 and 3/4 inputs. “6” indicates connecting 3 sets of
RCA’s to channels 1/2, 3/4 and 5/6.