Bahco ProfCut - Manual (Page 7)

Selection Table
There are a few things to consider when
selecting the right saw for the job. The following
steps and the table below will help you to
choose. Then complete the selection with other
saw features you prefer.
Contact us if you need more information!
Step 1. Select saw model: Superior, ProfCut or PrizeCut.
Step 2. Select saw according to column 1 – Type of saw/material.
Step 3. Select saw according to application – se column 5 and column 6 (Length).
- Precision work: Use fine cut saws with small teeth from 9/10 to 15/16 teeth/points per inch.
The length of the saw makes little difference.
- General work: Use medium cut saws with medium size teeth from 7/8 to 9/10 teeth/points per inch.
The length should be 18-22 inches for vigorous, thrusting strokes.
- Rough work: Use coarse cut saws with large teeth with 7/8 teeth/points per inch.
The length should be 22-26 inches for long, vigorous strokes.
Superior
GENERAL BLADE HANDLE
Type of Art. code EAN- Pack Application Length Toothing/TPI Low friction Thickness Type
saw/material code Qty in/mm coating of blade
COARSE 2700-24-XT7-HP 7311518191665 4 Timber, wet wood and tanalised 24/600 XT/7 Yes 1.03 mm Ergo, 2 component
COARSE 2700-22-XT7-HP 7311518191672 4 Timber, wet wood and tanalised 22/550 XT/7 Yes 1.03 mm Ergo, 2 component
MEDIUM 2600-22-XT-HP 7311518160777 4 Medium cutting 22/550 XT/9 Yes 1.03 mm Ergo, 2 component
MEDIUM 2600-19-XT-HP 7311518160760 4 Medium cutting 19/475 XT/9 Yes 1.03 mm Ergo, 2 component
Toolbox saw
FINE 2600-16-XT11-HP 7311518239527 4 Toolbox 16/400 XT/11 Yes 1.03 mm Ergo, 2 component
Laminate saw
LAMINATOR SUP-20-LAM 7311518258351 4 Laminate and wooden floors 20/500 XT/11 Yes 0.93 mm Ergo, 2 component
Small saws
TENON 3180-14-XT11-HP 7311518181390 4 Tenon saw 14/360 XT/11 Yes 0.75 mm Ergo, 2 component
VENEER 3240-14-XT11-HP 7311518243005 4 Veneer saw 14/360 XT/11 Yes 0.75 mm Ergo, 2 component
COMPASS 3150-12-XT9-HP 7311518181406 4 Compass saw 12/300 XT/9 Yes 1.03 mm Ergo, 2 component
ProfCut
GENERAL BLADE HANDLE
Type of Art. code EAN- Pack Application Length Toothing/TPI Low friction Thickness Type
saw/material code Qty in/mm coating of blade
ProfCut + base assortment
MEDIUM PCP-22-GT7 7311518263331 4 Medium cutting 22/550 GT/7 Yes 0.83 mm 2 component
MEDIUM PCP-19-GT7 7311518263317 4 Medium cutting 19/475 GT/7 Yes 0.83 mm 2 component
FINE PCP-22-GT9 7311518263348 4 Fine cutting 22/550 GT/9 Yes 0.83 mm 2 component
FINE PCP-19-GT9 7311518263324 4 Fine cutting 19/475 GT/9 Yes 0.83 mm 2 component
ProfCut base assortment
MEDIUM PC-22-GT7 7311518263393 4 Medium cutting 22/550 GT/7 No 0.83 mm 2 component
MEDIUM PC-19-GT7 7311518263362 4 Medium cutting 19/475 GT/7 No 0.83 mm 2 component
FINE PC-22-GT9 7311518263409 4 Fine cutting 22/550 GT/9 No 0.83 mm 2 component
FINE PC-19-GT9 7311518263379 4 Fine cutting 19/475 GT/9 No 0.83 mm 2 component
Toolbox saw
FINE PC-15-TBX 7311518263423 4 Fine cutting/Toolbox 15/380 GT/11 No 0.75 mm 2 component
Small saws
TENON PC-12-TEN 7311518263447 4 Tenon saw 12/300 UT/11 No 0.75 mm 2 component
VENEER PC-12-VEN 7311518263430 4 Veneer saw 12/300 UT/11 No 0.75 mm 2 component
COMPASS PC-12-COM 7311518263454 4 Compass saw 12/300 XT/9 No 1.03 mm 2 component
Fileable saws
MEDIUM PC-16-FILE-U7 7311518263461 4 Medium cutting/Fileable 16/400 UT/7 Fileable No 0.83 mm 2 component
MEDIUM PC-19-FILE-U7 7311518263478 4 Medium cutting/Fileable 19/475 UT/7 Fileable No 0.83 mm 2 component
MEDIUM PC-22-FILE-U7 7311518263485 4 Medium cutting/Fileable 22/550 UT/7 Fileable No 0.83 mm 2 component
MEDIUM PC-24-FILE-U7 7311518263492 4 Medium cutting/Fileable 24/600 UT/7 Fileable No 0.83 mm 2 component
Dove tail saws
DOVE TAIL PC-10-DTR 7311518263546 10 Dovetail right 10/250 UT/13 No 0.50 mm Wood
DOVE TAIL PC-10-DTL 7311518263553 10 Dovetail left 10/250 UT/13 No 0.50 mm Wood
DOVE TAIL PC-10-DTF 7311518263560 10 Dovetail flex 10/250 FT/15 No 0.50 mm Wood
Special application saws
Laminate saw
LAMINATOR PC-20-LAM 7311518258290 4 Laminate and wooden floors 20/500 XT/11 No 0.93 mm 2 component
Precision saw
PRECISION PC-20-PRC 7311518264291 4 Mitre/Precision/Fine 20/500 UT/9 No 0.93 mm 2 component
Timber saw
TIMBER PC-24-TIM 7311518263515 4 Coarse cutting/Fileable 24/600 FT/3.5 Fileable No 0.93 mm 2 component
Plaster saw
PLASTER PC-24-PLS 7311518263508 4 Plaster 24/600 GT/7 No 0.93 mm 2 component
General purpose saw
GEN. PURPOSE PC-15-GNP 7311518264307 4 General purpose 15/380 FT/15 No 0.75 mm 2 component
Polystyrene, foam saw
DECOR PC-16-DECO 7311518264987 4 Polystyrene, foam saw 16/400 Special No 0.75 mm 2 component
Concrete saws
255 7311518007843 1 Concrete/Carbide tip 30/750 30 Carbide tips No 1.6 mm 2 component
255-15/29 7311518007850 1 Concrete/Carbide tip 30/750 15 Carbide tips No 1.6 mm 2 component
Light Concrete saw
256-26 7311518000080 4 Light weight concrete 26/650 Non-Carbide No 1.15 mm 2 component
PrizeCut
GENERAL BLADE HANDLE
Type of Art. code EAN- Pack Application Length Toothing/TPI Low friction Thickness Type
saw/material code Qty in/mm coating of blade
UNIVERSAL NP-22-U7/8-HP 7311518034399 10 Universal 22/550 UT/7 No 0.83 mm 1 component
UNIVERSAL NP-19-U7/8-HP 7311518241452 10 Universal 19/475 UT/7 No 0.83 mm 1 component
UNIVERSAL NP-16-U7/8-HP 7311518241773 4 Universal 16/400 UT/7 No 0.83 mm 1 component
Small saws
TENON NP-12-TEN 7311518263959 10 Tenon saw 12/300 UT/13 No 0.75 mm 1 component
VENEER NP-12-VEN 7311518264260 4 Veneer saw 12/300 UT/13 No 0.75 mm 1 component
COMPASS NP-12-COM 7311518264277 4 Compass saw 12/300 UT/7 No 1.20 mm 1 component
General purpose saw
FINE 300-14-F15/16-HP 7311518005955 4 General purpose 14/360 FT/15 No 0.75 mm 1 component
Concrete saws
NP-CONC 7311518264918 4 Concrete/Carbide tip 25/620 34 Carbide tips No 2.00 mm Wood
NP-CONC-17/34 7311518264925 4 Concrete/Carbide tip 25/620 17 Carbide tips No 2.00 mm Wood