Allen&Heath EtherSound User Manual

Ilive, Es2 (ethersound) option, Ethersound

iLive ES2 Option Instructions AP7651 issue 2

M-ES-V2 is one of several plug-in card options that may be fitted to
the iLive Series. It houses the

Auvitran AVDM

card to provide a

multi channel digital audio network that can link iLive MixRacks and
Surfaces, transport and split signals between systems and distribute
audio around a venue using CAT5 cables.

Note 1

To fit to the iDR10 and iLive Surfaces, the Remote Audio 2

(RAB2) module is required. Systems fitted with the earlier Remote
Audio modules may be upgraded by replacing them with RAB2.

Note 2

M-ES-V2 is compatible with EtherSound built into the

earlier iLive system Remote Audio modules. The older

Auvitran AVD

cards can be reused in the newer Remote Audio 2 (RAB2) modules
by fitting them to a carrier frame kit, part number M-ES-V1-BASE.
The AVD cards can not be used in the iDR-32 or 48 Port B slot.

EtherSound

is an industry standard, low latency digital audio

networking system using off-the-shelf Ethernet components and
invented by

Digigram

. It transports 64 channels of bi-directional

audio over CAT5 cable. To find out more about setting up and using
EtherSound refer to the Digigram and EtherSound web sites.

Cables CAT5E cable up to 100m (330’) may be used depending
on cable type. Refer to the Digigram web site for approved cable
types and their maximum tested lengths. We recommend you use
tour grade cable fitted with locking RJ45 connectors. Allen & Heath
can supply an 80m drum of

Neutrik

EtherFlex cable fitted with

EtherCon connectors, part number AH7000.

RX/TX Both flash to indicate that the network is linked and active.

ES CONTROL PORT Use this port to connect a laptop running the

Auvitran EtherSound Monitor

application. This lets you check and

set up the network routing and parameters. For standard operation
with iLive it is not usually necessary to access these settings.

IN and OUT A single cable connects EtherSound between two
devices. Connect OUT of the master device to IN of the slave
device. Do not connect two cables. IN and OUT relates to clock
master, not audio in and out. The single cable carries both input and
output signals (64 channels each way).

Fitting the card

Make sure the system is switched off. Remove the 2 screws
securing the blank panel over Port A (MixRack or Surface) or Port B
(MixRack only). Slide the M-ES-V2 card into the slot and press it
firmly into the mating connector. Secure the card in place using the
2 screws. Power the system up. The card is recognised by the
system and its status displayed on the Surface screen Status page.

Assigning the audio

Use the Surface or Editor

OUTPUTS

page to assign sources and destinations for the

EtherSound channels.

This product complies with the European
Electromagnetic Compatibility directives 89/336/EEC &
92/31/EEC.

NOTE: Any changes or modifications to the
equipment not approved by Allen & Heath could void
the compliance of the equipment. Whilst we believe
the information in this guide to be reliable we do not
assume responsibility for inaccuracies. We also reserve
the right to make changes in the interest of further
product development.

IMPORTANT :

Do not install the equipment where it is

subject to moisture, heat or vibration.

Connect only to the EtherSound port on other

equipment.

iLive

ES2 (EtherSound) Option

AP7651

Instructions

Part number M-ES-V2-A

Port B

Lnk

Err

Lnk

Err

NET

BRI

Port B

Port A

PAFL

(CHK)

REMOTE AUDIO 2

SYSTEM LOCK

SYNC

OUT

AUDIO

CLOCK

Lnk/Act

Error

Lnk/Act

Error

Lnk/Act

Error

NETWORK

BRIDGE

CONTROL

ES V2

RX
TX

OUT

CONTROL

PORT

ALLEN&HEATH

Note

For firmware

V1.5

this option is

not supported in the iLive Surface RAB2
module Port B. The only option
supported in this location is the MMO
module (ADAT, iDR link).