Allen&Heath MixWizard3 12M - Manual (Page 12)

12 WZ 3 12M User Guide
The Console Connectors
CHANNEL INPUT Balanced XLR input pin 2 hot. Accepts
microphone or line level signals. For very hot mic or for line signals press
the channel PAD (LINE) switch. For unbalanced sources use a cable or
adapter that connects XLR pin 3 to pin 1.
WARNING: Do not connect unbalanced sources or cables to
the XLR input when 48V phantom power is selected. To avoid loud
clicks always turn the channel off by pressing MUTE when switching
+48V on or off, and when plugging or unplugging cables.
BUILT-IN MIC SPLITTER A passive splitter passes each channel
XLR input directly through to an XLR output to send the signal to another
console such as Front-of-House or recording. The mic signal can feed the
monitor and the FOH console at the same time. Connect the split outputs
to the multicore feeding the FOH console using XLR cables.
NOTE: Phantom power can be switched from either the monitor or
the FOH console. If switched from FOH then make sure GND LIFT is
not selected. If it is necessary to select GND LIFT then phantom
power should be switched from the monitor console. No harm will be
done to the consoles if phantom power is switched from both
consoles at the same time.
GND LIFT Disconnects the pin 1 ground connection between the input
XLR and the split output XLR. Press this if there is a problem with a
venue ground loop causing audible hum when connecting the splitter to
the second console. A single ground lift switch is provided next to CH1
input. This affects the ground connection to all the channel split outputs.
48V
2= +
IN
SPLIT
LIFT
To other channels
WARNING: THIS APPARATUS MUST BE EARTHED
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
RISK OF ELECTRIC SHOCK
CAUTION
DO NOT OPEN
100 - 240V~ 47-63Hz 45W MAX
AC MAINS IN ~
FUSE
T630mA L 250V 20mm
ON
I 0
OFF EXTERNAL DC IN
ONLY USE RECOMMENDED ALLEN&HEATH POWER SUPPLY.
REFER TO USER GUIDE FOR DETAILS.
BACKUP SUPPLY
IN
INSERT
OUT
1
12M 3 MixWizard WZ ALLEN&HEATH
INSERT
SPLIT
1
INSERT
OUT
2
GROUND LIFT
IN
SPLIT
INSERT
2
INSERT
OUT
3
INSERT
OUT
4
INSERT
OUT
5
INSERT
OUT
6
INSERT
OUT
7
INSERT
OUT
8
INSERT
OUT
9
INSERT
OUT
10
INSERT
OUT
11
INSERT
OUT
12
IN
SPLIT
INSERT
3
IN
SPLIT
INSERT
4
IN
SPLIT
INSERT
5
IN
SPLIT
INSERT
6
IN
SPLIT
INSERT
7
IN
SPLIT
INSERT
8
IN
SPLIT
INSERT
9
IN
SPLIT
INSERT
10
IN
SPLIT
INSERT
11
IN
SPLIT
INSERT
12
IN
SPLIT
INSERT
13
IN
SPLIT
INSERT
14
IN
SPLIT
INSERT
15
IN
SPLIT
INSERT
16
USER OPTION PORT A
L R L R
MONITOR
EXT MONITOR IN
USER OPTION PORT B
OUT
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
Serial No.
(1) this device may not cause harmful interference, and
ENGINEERED IN ENGLAND BY ALLEN & HEATH LIMITED
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
ATTENTION: REMPLACER PAR UN FUSIBLE STRICTEMENT IDENTIQUE EN VALEURS.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. REPLACE FUSE WITH SAME TYPE AND RATING.