JLG 110HX Parts Manual User Manual
Illustrated parts manual
This manual is related to the following products:
Table of contents
Document Outline
- SECTION 1 FRAME
- FIGURE 1-1. STEERING AND AXLE/WHEEL DRIVE INSTALLATIONS
- FIGURE 1-2. DRIVE HUB ASSEMBLY
- FIGURE 1-3. DRIVE BRAKE ASSEMBLY - AUSCO
- FIGURE 1-4. DRIVE BRAKE ASSEMBLY - MICO
- FIGURE 1-5. DRIVE MOTOR ASSEMBLY - VICKERS
- FIGURE 1-6. DRIVE MOTOR ASSEMBLY - SAUER-DANFOSS
- FIGURE 1-7. VALVES AND SWITCHES INSTALLATIONS (FRAME MOUNTED)
- FIGURE 1-8. TOW PACKAGE INSTALLATIONS
- SECTION 2 TURNTABLE
- FIGURE 2-1. TURNTABLE, BOOM AND CUTOUT SWITCH INSTALLATIONS (4620044 TURNTABLE MACHINES)
- FIGURE 2-2. TURNTABLE, BOOM AND CUTOUT SWITCH INSTALLATIONS (4620078 TURNTABLE MACHINES)
- FIGURE 2-3. CONTROL VALVES AND TILT INDICATOR INSTALLATIONS
- FIGURE 2-4. CONTROL VALVES ASSEMBLY (VICKERS) (PRIOR TO OCTOBER 1994)
- FIGURE 2-5. CONTROL VALVES ASSEMBLY (VICKERS) (OCTOBER 1994 TO PRESENT)
- FIGURE 2-6. CONTROL VALVE ASSEMBLY - BANG-BANG WITH DUMP SECTION (PRIOR TO JUNE 1995)
- FIGURE 2-7. CONTROL VALVE ASSEMBLY - BANG-BANG WITH DUMP SECTION (JUNE 1995 TO PRESENT)
- FIGURE 2-8. ACCESSORY VALVE ASSEMBLY (MILLER) (MACHINES BUILT THROUGH 1989)
- FIGURE 2-9. ACCESSORY VALVE ASSEMBLY (MACHINES BUILT 1990 TO PRESENT)
- FIGURE 2-10. CONTROL VALVE ASSEMBLY - 1 SECTION BANG-BANG (100HX+10/110HXER MACHINES)
- FIGURE 2-11. SWING DRIVE, BEARING AND LOCK INSTALLATIONS
- FIGURE 2-12. SWING MOTOR ASSEMBLY - NICHOLS
- FIGURE 2-13. SWING BRAKE ASSEMBLY (PRIOR TO APRIL 1992)
- FIGURE 2-14. SWING BRAKE ASSEMBLY (APRIL 1992 to PRESENT)
- FIGURE 2-15. SWING HUB ASSEMBLY
- FIGURE 2-16. ROTARY COUPLING AND COLLECTOR RING ASSEMBLY AND INSTALLATION
- FIGURE 2-17. DEUTZ ENGINE INSTALLATION WITHOUT NOISE REDUCTION (BUILT PRIOR TO OCTOBER 1992)
- FIGURE 2-18. DEUTZ ENGINE INSTALLATION WITH NOISE REDUCTION (BUILT OCTOBER 1992 TO PRESENT)
- FIGURE 2-19. ADECO THROTTLE COMPONENTS INSTALLATION - DEUTZ ENGINE MACHINES
- FIGURE 2-20. GENERATOR INSTALLATIONS - DEUTZ ENGINE MACHINES
- FIGURE 2-21. PUMP COUPLING INSTALLATION
- FIGURE 2-22. MAIN PUMP ASSEMBLY
- FIGURE 2-23. TANKS INSTALLATION
- FIGURE 2-24. GROUND CONTROLS INSTALLATION
- FIGURE 2-25. LOAD MANAGEMENT INSTALLATION
- FIGURE 2-26. HOODS AND ALARM INSTALLATION (MACHINES WITH 4620044 TURNTABLE)
- FIGURE 2-27. HOODS AND ALARM INSTALLATION (MACHINES WITH 4620078 TURNTABLE)
- SECTION 3 BOOM
- FIGURE 3-1. BOOM ASSEMBLY COMPONENTS INSTALLATION
- FIGURE 3-1. BOOM ASSEMBLY COMPONENTS INSTALLATION (SHEET 2 OF 2)
- FIGURE 3-2. CHAIN ADJUSTER ASSEMBLIES
- FIGURE 3-3. EXTEND-A-REACH INSTALLATIONS (PRIOR TO MAY 1992) (100HX+10 & 110HXER ONLY)
- FIGURE 3-4. EXTEND-A-REACH INSTALLATIONS (MAY 1992 TO PRESENT) (100HX+10 & 110HXER ONLY)
- FIGURE 3-5. BOOM LENGTH INDICATOR AND LIMIT SWITCHES INSTALLATION
- FIGURE 3-6. BROKEN CHAIN LIMIT SWITCH INSTALLATION (GERMAN/AUSTRIAN SPECS BUILT PRIOR TO S/N 28224)
- FIGURE 3-7. BOOM WIPERS INSTALLATION
- SECTION 4 PLATFORMS
- FIGURE 4-1. PLATFORM COMPONENTS INSTALLATION - 100HX/110HX
- FIGURE 4-2. PLATFORM COMPONENTS INSTALLATION - 100HX+10/110HXER (PRIOR TO MAY 1992)
- FIGURE 4-3. PLATFORM COMPONENTS INSTALLATION - 100HX+10/110HXER (MAY 1992 TO PRESENT)
- FIGURE 4-4. ROTATOR MOTOR ASSEMBLY
- FIGURE 4-5. CONSOLE BOX ASSEMBLY (PRIOR TO SEPTEMBER 1991)
- FIGURE 4-6. CONSOLE BOX ASSEMBLY (SEPTEMBER 1991 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLIES - OEM
- FIGURE 4-8. OPTIONAL COMMON PLATFORM MOUNTED COMPONENTS
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE EXTENSION CYLINDER ASSEMBLY
- FIGURE 5-2. AXLE LIFT CYLINDER ASSEMBLY
- FIGURE 5-3. PLATFORM LEVEL CYLINDER ASSEMBLY (100HX & 110HX BUILT PRIOR TO MAY 1992)
- FIGURE 5-4. LEVEL CYLINDER ASSEMBLY (100HX & 110HX)
- FIGURE 5-5. PLATFORM LEVEL CYLINDER ASSEMBLY (100HX+10 & 110HXER BUILT PRIOR TO MAY 1992)
- FIGURE 5-6. PLATFORM LEVEL CYLINDER ASSEMBLY (100HX+10 & 110HXER)
- FIGURE 5-7. LIFT CYLINDER ASSEMBLY - BOOM (PRIOR TO MAY 1992)
- FIGURE 5-8. LIFT CYLINDER ASSEMBLY - BOOM (MAY 1992 TO PRESENT)
- FIGURE 5-9. LIFT CYLINDER ASSEMBLY - BOOM (GERMAN TUV STYLE)
- FIGURE 5-10. LIFT CYLINDER ASSEMBLY - EXTEND-A-REACH (100HX+10 & 110HXER ONLY)
- FIGURE 5-11. MASTER CYLINDER ASSEMBLY
- FIGURE 5-12. STEER CYLINDER ASSEMBLY
- FIGURE 5-13. TELESCOPE CYLINDER ASSEMBLIES
- FIGURE 5-14. CYLINDER BELLOWS INSTALLATION
- SECTION 6 HYDRAULICS
- FIGURE 6-1. HYDRAULIC DIAGRAM LIST
- FIGURE 6-2. HYDRAULIC DIAGRAM - AXLE EXTENSION & STEER (WITHOUT TOW PACKAGE & WITH DUAL FRAME JACKS)
- FIGURE 6-3. HYDRAULIC DIAGRAM - BRAKE WITH PRESSURE REDUCING VALVE (USED WITH AUSCO DRIVE BRAKES)
- FIGURE 6-4. HYDRAULIC DIAGRAM - DRIVE
- FIGURE 6-5. HYDRAULIC DIAGRAM - EXTEND-A-REACH (100HX+10 AND 110HXER)
- FIGURE 6-6. HYDRAULIC DIAGRAM - LEVEL
- FIGURE 6-7. HYDRAULIC DIAGRAM - LIFT
- FIGURE 6-8. HYDRAULIC DIAGRAM - PUMP
- FIGURE 6-9. HYDRAULIC DIAGRAM - ROTATE
- FIGURE 6-10. HYDRAULIC DIAGRAM - SEQUENCE LINE
- FIGURE 6-11. HYDRAULIC DIAGRAM - SWING
- FIGURE 6-12. HYDRAULIC DIAGRAM - TELESCOPE
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS