B & K MZ-128 User Manual
B & K Remote control

POWER
POWER
1
1
2
2
3
3
4
4
7
7
5
5
8
8
0
0
6
6
9
9
ENTER
ENTER
IN 8
IN 8
TUNE-
TUNE-
SAVE
SAVE
MENU
MENU
EXIT
EXIT
LOUD
LOUD
OFF
OFF
MUTE
MUTE
IN 9
IN 9
+10
+10
AM
AM
M
M
T+
T+
S+
S+
FM
FM
V+
V+
T-
T-
S-
S-
B
& K Components, Ltd.
Model MZ-128
SEL
SEL
ENTER
ENTER
VOLUME
VOLUME
PRESET
PRESET
ON/OFF
ON/OFF
B+
B+
B-
B-
Õ
®
°
¯
ZONE
ZONE
VIDEO +
VIDEO +
BASS
BASS
TREBLE
TREBLE
SOURCE
SOURCE
ST/M
ST/M
LOUDNESS
LOUDNESS
DEDICATED
DEDICATED
D-IN
D-IN
TUNE+
TUNE+
STA-
STA-
STA+
STA+
UP
UP
DOWN
DOWN
L
E
F
T
L
E
F
T
R
I
G
H
T
R
I
G
H
T
B
&
K CT Series MZ-128 Remote Controller Reference Sheet
The MZ-128 Remote Controller has multiple useful functions:
1) The MZ-128 Remote Controller may be used to control and setup a CT610/310/600.
2) The
learning keypads etc...
3) The
may be set to source
code sets 000-128
and 999.
MZ-128 may be used as a source of IR for use in programming
MZ-128
the B
&
K IR functions listed below, for
Setup the MZ-128 to use a discrete B
&
K code set:
1) Install 4 AAA batteries into the remote. Observe polarity.
2) Press and hold the B
&
K and MUTE buttons simultaneously for two seconds. The LED will
light up solid red and stay illuminated.
3) Firmly press the desired B
&
K three digit code set. Always use three digits (i.e. 0-1-1 default
for Zone A)
4) Press the B
&
K button again to confirm setup. The red LED will blink three times when the IR
CODE SET 000-128
MZ-128 BUTTON
B
&
K IR FUNCTION
MZ-128 BUTTON
B
&
K IR FUNCTION
[POWER STATE]
[TUNER]
B&K
POWER ON
AM
SELECT THE AM BAND
POWER
POWER TOGGLE
FM
SELECT THE FM BAND
OFF
POWER OFF
TUNE +
TUNE FREQUENCY UP
TUNE -
TUNE FREQUENCY DOWN
[VOLUME]
STA +
TUNER FAV PRESET UP
MUTE
MUTE TOGGLE
STA -
TUNER FAV PRESET DOWN
VOLUME
MASTER VOL UP
M
STEREO / MONO
VOLUME
MASTER VOL DOWN
[NAVIGATION]
[TONE CONTROL]
MENU
MENU UP/DOWN LEVEL
B+
BASS UP
LEFT
LEFT OR BALANCE (L)
B-
BASS DOWN
RIGHT
RIGHT OR BALANCE (R)
T+
TREBLE UP
SEL/ENTER
SELECT OR ENTER
T-
TREBLE DOWN
UP
UP
LOUD
LOUDNESS TOGGLE
DOWN
DOWN
SAVE
SAVE
[INPUT SOURCE]
EXIT
TOTAL EXIT FROM ALL MENUS
S+
SOURCE UP
ZONE
ZONE SELECT
S-
SOURCE DOWN
V+
VIDEO SOURCE UP
[NUMERIC]
D-IN
ZONE DEDICATED IN
0
0
AM
TUNER AM
1
1
FM
TUNER FM
2
2
IN 1
IN 1 OR [V1]
3
3
IN 2
IN 2 OR [V2]
4
4
IN 3
IN 3 OR [TV]
5
5
IN 4
IN 4 OR [DVD]
6
6
IN 5
IN 5 OR [CD]
7
7
IN 6
IN 6 OR [SAT]
8
8
IN 7
IN 7 OR [TAPE]
9
9
IN 8
IN 8 OR [V4]
+10
+10
IN 9
IN 9 OR [V5]
[FAVORITE PRESET]
PRESET
FAVORITE PRESET UP
PRESET
FAVORITE PRESET DN
CODE SET 999
MZ-128 BUTTON
B
&
K IR FUNCTION
[B
&
K ALL COMMANDS]
ON/B
&
K/POWER ALL B
&
K POWER ON
OFF
ALL B
&
K POWER OFF
VOLUME ALL
B
&
K VOLUME UP
VOLUME ALL
B
&
K VOLUME DOWN
0
ALL B
&
K VOLUME 0 DB
2
ALL B
&
K VOLUME -20 DB
4
ALL B
&
K VOLUME -40 DB
6
ALL B
&
K VOLUME -60 DB
MUTE
ALL B
&
K MUTE TOGGLE
B
& K
B
&
K
MZ-128 Default Factory Code-Set is: 0-0-0 Whole House Control
Code-Set 128 Simply Explained
Code-Set 128 is a special code-set which
allows individual control of the Hardware Zone
that the IR Data is received by. It will not function
when received by the unit’s front panel. I.e., Two
keypads are plugged into Zone A & B’s Control
I/O Ports, when the remote comes into IR view
of the keypad in Zone A, the 128 Code-set
remote will only control Zone A, when in Zone A.
Take that same remote into Zone B and it will
only control Zone B.