Troubleshooting, Replacement parts, Replacement parts ... continued – Steele Products SP-PB101 User Manual
Page 8
WARNING:
For your safety, turn the switch OFF and remove the safety key. Unplug the
power cord from the outlet before maintaining or lubricating the saw.
PROBLEM
Saw will not start.
Does not make accurate 45°
and 90° rip cuts.
Material pinches blade when
ripping.
Material binds on splitter.
Saw makes unsatisfactory
cuts.
Material kicked back from
blade.
Blade does not raise or tilt
freely.
Blade does not reach full
speed.
Machine vibrates excessively.
Does not make 45°and 90°
cross cuts.
PROBABLE CAUSE
1. Saw not plugged in.
2. Fuse blown or circuit breaker tripped.
3. Cord damaged.
4. Overload or low voltage.
1. Positive stop not adjusted correctly.
2. Tilt angle pointer not set correctly.
1. Rip fence not aligned with blade.
2. Warped wood, edge against fence is
not straight.
Splitter not aligned correctly with blade.
1. Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
4. Incorrect blade for work.
5. Gum or pitch on table causing erratic
feed.
1. Rip fence out of alignment.
2. Splitter not aligned with blade.
3. Feeding stock without rip fence.
4. Splitter not in place.
5. Dull blade.
6. The operator letting go of material
before it is past the saw blade.
7. Miter angle lock knob is not tight.
Sawdust and dirt in elevation and tilting
mechanisms.
1. Extension cord too tight or too long.
2. Low house voltage.
1. Saw not mounted securely to stand or
workbench.
2. Stand or bench on uneven floor.
3. Damaged saw blade.
Miter gauge out of adjustment.
REMEDY
1. Plug in the saw.
2. Replace fuse or reset circuit breaker.
3. Have cord replaced by an authorized service
center.
4. Turn the saw switch to OFF, wait 5 minutes,
push the reset switch, and turn the saw ON.
1. Check blade with square and adjust positive
stop.
2. Check blade with square and adjust pointer
to zero.
1. Check and adjust rip fence.
2. Select another piece of wood.
Check and align splitter with blade.
1. Replace blade.
2. Turn blade around.
3. Remove blade and clean with turpentine and
coarse steel wool.
4. Change the blade.
5. Clean table with turpentine and steel wool.
1. Align rip fence with miter gauge.
2. Align splitter with blade.
3. Install and use rip fence.
4. Install and use splitter (with guard).
5. Replace blade.
6. Push material all the way past blade before
releasing work.
7. Tighten knob.
Brush or blow out loose dust and dirt.
1. Replace with adequate size cord.
2. Contact your electric company.
1. Tighten all mounting hardware.
2. Reposition on flat level surface. Fasten to
floor if necessary.
3. Replace blade.
Adjust miter gauge.
Troubleshooting
28
Replacement parts
When servicing your STEELE® 10" Bench Saw, use identical STEELE® replacement parts only.
Use of any other parts may cause product damage. Any and all servicing of the
bench saw should be performed by a qualified service technician.
WARNING: ANY ATTEMPT TO REPAIR OR REPLACE ELECTRICAL PARTS ON THIS TOOL
MAY CREATE AHAZARD UNLESS REPAIR IS DONE BY QUALIFIED SERVICE TECHNICIANS.
29
Replacement parts ... continued
30
APA Parts No. No. Description
QTY
APA Parts No. No. Description
QTY
PB101-01-SD
PB101-02-SD
PB101-03-SD
PB101-04-SD
PB101-05-SD
PB101-06-SD
PB101-07-SD
PB101-08-SD
PB101-09-SD
PB101-10-SD
PB101-11-SD
PB101-12-SD
PB101-13-SD
PB101-14-SD
PB101-15-SD
PB101-16-SD
PB101-17-SD
PB101-18-SD
PB101-19-SD
PB101-20-SD
PB101-21-SD
PB101-22-SD
PB101-23-SD
PB101-24-SD
PB101-25-SD
PB101-26-SD
PB101-27-SD
PB101-28-SD
PB101-29-SD
PB101-30-SD
PB101-31-SD
PB101-32-SD
PB101-33-SD
PB101-34-SD
PB101-35-SD
PB101-36-SD
PB101-37-SD
PB101-38-SD
PB101-39-SD
PB101-40-SD
PB101-41-SD
PB101-42-SD
PB101-43-SD
PB101-44-SD
PB101-45-SD
PB101-46-SD
PB101-47-SD
PB101-48-SD
PB101-49-SD
PB101-50-SD
PB101-51-SD
PB101-52-SD
PB101-53-SD
PB101-54-SD
PB101-55-SD
PB101-56-SD
PB101-57-SD
PB101-58-SD
PB101-59-SD
PB101-60-SD
PB101-61-SD
PB101-62-SD
PB101-63-SD
PB101-64-SD
PB101-65-SD
PB101-66-SD
PB101-68-SD
PB101-68-SD
PB101-69-SD
PB101-70-SD
PB101-71-SD
PB101-72-SD
PB101-73-SD
PB101-74-SD
PB101-75-SD
PB101-76-SD
PB101-77-SD
PB101-78-SD
PB101-79-SD
PB101-80-SD
PB101-81-SD
PB101-82-SD
PB101-83-SD
PB101-84-SD
PB101-85-SD
PB101-86-SD
PB101-87-SD
PB101-88-SD
PB101-89-SD
PB101-90-SD
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
3
Screw (GB6562-86 STx16)
1
Rear cover
1
Strain relief
2
Brush holder
2
Carbon brush
1
Wire connector
1
Motor housing
6
Screw(GB818-85 M5x30)
11
Spring washer(GB93-87 5)
8
Flat washer (GB95-85 5)
1
Stator
2
Screw (GB818-85 M5x78)
1
Bearing(GBøT276-94 629z)
1
Rotor
1
Bearing(GBøT276-94 6201)
1
Wind washer
1
Gear box
1
C-ring(GB894.1-86 14)
1
Bearing(GBøT276-94 607z)
1
Gear
1
Spindle
1
Key (GB61095-79 A5x12)
1
C-ring (GB894.3-86 35)
1
Bearing(GBøT276-94 6003)
1
Bushing
1
Gear box cover
1
In flange
1
Blade
1
Out flange
1
Blade nut
1
Pin
1
Screw (GB5781-86 M6x85)
1
Pin
1
Link plate
14
Lock nut(GBøT889.1-2000 M6)
1
Adjustment support
2
Nut
1
Adjustment pin
2
Bolt (GB5781-86 M8x18)
1
Support board A
1
Scale board
2
Screw (GB818-85 M5x10)
2
Nut (GBøT889.1-2000 M8)
1
Indicator
1
1
5
1
1
1
1
2
1
1
1
1
4
1
12
3
3
1
4
1
1
4
16
1
5
3
3
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
6
Block plate
Finger board
Wave washer(GB955-87 10)
Spring
Adjustment bolt
Pin (GB879-86 2.5x22)
Control wheel
Nut (GB6170-86 M8)
Wheel label
Wheel handle
Screw
Gear washer(GB8622-87 4)
Flat washer(GB95-85 4)
Screw(GB818-85 M4x10)
Lock washer(GB62.2-87 6)
Bolt (GB5781-86 M6x16)
Shaft bube
Screw
Big nut (GB6170-86 M6)
Washer plate
Lock knob
Screw
Spring washer(GB93-87 6)
Support board B
Flat washer(GB95-85 6)
Spring pin(GB879-86 4x8)
Nut
Spring
Flat washer (GB848-85 10)
Nut (GB6170-86 M5)
Pivot rod
Underlay
Screw(GB70-85 M5x22)
Rear axis
Plate
Screw(GB819-85 M6x25)
Screw(GB70-85 M5x12)
Table insert
Washer (GB862.2-87 5)
Screw
Screw(GB70-85 M6x25)
Work table
Bolt (GB5781-86 M6x25)
Gear washer(GB862.2-87 5)
Hex screw(GB70-85 M5x8)
Press plate
Replacement parts
31
APA Parts No. No. Description
QTY
APA Parts No. No. Description
QTY
PB101-91-SD
PB101-92-SD
PB101-93-SD
PB101-94-SD
PB101-95-SD
PB101-96-SD
PB101-97-SD
PB101-98-SD
PB101-99-SD
PB101-100-SD
PB101-101-SD
PB101-102-SD
PB101-103-SD
PB101-104-SD
PB101-105-SD
PB101-106-SD
PB101-107-SD
PB101-108-SD
PB101-109-SD
PB101-110-SD
PB101-111-SD
PB101-112-SD
PB101-113-SD
PB101-114-SD
PB101-115-SD
PB101-116-SD
PB101-117-SD
PB101-118-SD
PB101-119-SD
PB101-120-SD
PB101-121-SD
PB101-122-SD
PB101-123-SD
PB101-124-SD
PB101-125-SD
PB101-126-SD
PB101-127-SD
PB101-128-SD
PB101-129-SD
PB101-130-SD
PB101-131-SD
PB101-132-SD
PB101-133-SD
PB101-134-SD
PB101-135-SD
PB101-136-SD
PB101-137-SD
PB101-138-SD
PB101-139-SD
PB101-140-SD
PB101-141-SD
PB101-142-SD
PB101-143-SD
PB101-144-SD
PB101-145-SD
PB101-146-SD
PB101-147-SD
PB101-148-SD
PB101-149-SD
PB101-150-SD
PB101-151-SD
PB101-152-SD
PB101-153-SD
PB101-154-SD
PB101-155-SD
PB101-156-SD
PB101-157-SD
PB101-158-SD
PB101-159-SD
PB101-160-SD
PB101-161-SD
PB101-162-SD
PB101-163-SD
PB101-164-SD
PB101-165-SD
PB101-166-SD
PB101-167-SD
PB101-168-SD
PB101-169-SD
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
1
Scale label
3
Rivet (GB827-86 2x6)
11
Screw(GB848-85 ST4x12)
2
Spring plate
2
Fence base
1
Base
1
Data label
1
Inner plate
9
Screw(GB819-85 M4x8)
1
Gear plate
8
Screw(GB848-85 ST4x16)
2
Switch base
12
Switch
3
Circuit breaker
3
Breaker nut
1
Switch box
1
Dustproof ring
1
Wire holder
2
Screw (GB848-85 ST4x16)
1
Strain relief
1
Spindle
1
Dust port cover
2
Screw (GB848-85 ST4x16)
1
Nut (GB6170-86 M4)
1
Mitre gauge storage
1
Spring plate
2
Spring washer(GB93-87 4)
1
Screw (GB818-85 M4x10)
4
Rubber foot
1
Rear plate
1
Spring
1
Spring defence board
1
Fence
1
Bolt
2
Hex bolt(GB5871-86 M6x10)
1
Washer plate
1
Fence support
2
Long nut
1
Spring pin (GB878-86 3x22)
2
Bias wheel
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
1
2
1
2
6
1
1
1
6
1
1
1
1
1
1
1
4
1
Pin
Fence handle
Pin
Front nip board
Screw (GB818-86 M4x6)
Indicator
Pin
Guide ruler
Gauge pointer
Spring washer
Screw (GB818-86 M4X6)
Mitre gauge
Angle bolt
Lock knob
Knob cover
Blade guard
Block pin
Spring washer
Guard arm
Bush
Spring
Follow blade board
Anti-kickback pawl
Bolt (GB5781-86 M6x22)
Bolt (GB5781-86 M6x40)
Flat washer(GB95-85 6)
Block bushing-R
Spring pin(GB879-86 3x10)
Block bushing-L
Hex bolt(GB70-85 M6x12)
Press plate
Hex bolt(GB70-85 M5x20)
Flat washer (B95-86-5)
Support base
Dado inser
Wrench
Open ended wrench
Push stick
Power cord