Philips 27DV693R - Manual (Page 2)

2
H
OOKING UP THE
TV
1
ANT 75‰
L/Mono
Monitor out VIDEO
S-VIDEO
AV1 in Y Pb Pr
AV2 in
AUDIO R COMPONENT VIDEO INPUT
Y our Cable TV input into your home may be a single (75 ohm)
cable or use a cable box decoder. In either case the connec-
tion is very simple.
Follow the steps below to connect your cable signal to your new
television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
1 Connect the open end of the round Cable Company sup-
plied cable to the 75 Ω input on the TV. Screw it down finger
tight.
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV. The sound
from the cable box will be mono.
2 Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
3 Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
4 Connect the other end of the round coaxial cable to the
75 Ω input on the back of the television. Screw it down finger
tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the TV to the corre-
sponding channel. Once tuned, change channels at the cable box, not
the television.
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
5 Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
6 Using a RCA type Video Cable, connect one end of the
cable to the Video (or ANT, your cable box may be labeled
differently) Out jack on the cable box and the other end to the
AV1 Video Input on the TV.
7 Using a RCA type Audio Left and Right Cable, connect one
end to the left and right Audio Out L & R jacks on the
cable box. Connect the other end to the AV1 Audio L & R
Input jacks on the TV.
NOTE: Use the Channel +, or – buttons on the TV remote control to
tune to the AV1 channel for the cable box signal. Once tuned, change
channels at the cable box, not the television.
C
ABLE
/C
ABLE
B
OX
TV
CABLE
IN
TO
TV VIDEO
OUT
L R
AUDIO
OUT
3 4
OUTPUT
CH
TO TV CABLE
IN
4
2
3
ANT 75‰
L/Mono
Monitor out VIDEO
S-VIDEO
AV1 in
Y Pb Pr
AV2 in
AUDIO R COMPONENT VIDEO INPUT
24
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
ANT 75‰
L/Mono
Monitor out VIDEO
S-VIDEO
AV1 in
Y Pb Pr
AV2 in
AUDIO R COMPONENT VIDEO INPUT
5
6
7
OUTPUT
CH
3 4
Direct Cable Connection:
Cable Box with RF Inputs and Outputs Connection:
Cable signal
coming from
Cable Company
(Round 75 Ω
coaxial cable)
Jack Panel Back of TV
Jack Panel Back
of Cable Box
Cable Signal
IN from the
Cable
Company
Round 75 Ω
Coaxial Cable
Jack Panel Back of TV
A combination antenna receives normal broadcast chan-
nels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75 Ω (ohm) antenna plug on
the back of your TV, and that’s where the antenna goes.
1 If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2 Push the round end of the adapter (or antenna) onto the
75 Ω (ohm) plug on the back of the TV. If the round end of
the antenna wire is threaded, screw it down finger tight.
A
NTENNA
TV
1
2
ANT 75‰
L/Mono Monitor out VIDEO
S-VIDEO
AV1 in Y Pb Pr
AV2 in
AUDIO R COMPONENT VIDEO INPUT
Antenna Connection:
Jack Panel Back of TV Round 75 Ω Coaxial
Cable from Antenna
Twin
Lead Wire
300 to 75-ohm
Adapter
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna receives normal
broadcast channels 2-13 (VHF) and 14-69 (UHF).
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN
from the Cable
Company
Jack Panel Back
of Cable Box with A/V Outputs
Jack Panel Back of TV
Audio Cables
L & R (Red, White) Video Cable (Yellow)
Output Channel Switch